The machine locks up with the following message displayed on the monitor during the initial boot. usb0: OHCI version 1.8, legacy support usb0: SMM does not respond, resetting usb0: <OHCI (generic) USB controller> on ohciO usb0: USB revision 1.0 uhub0: <ATI OHCI root hub. class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 3 ports with 3 removable, self powered ohci1: <OHCI (generic) USB controller> mem 0xfbcfd000 0xfbcfdfff irq 16 at devic e 18.1 on pci0 ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfbcfd000 ohci1: [GIANT-LOCKED] ohci1: [ITHREAD] usb1: OHCI version 1.0, legacy support usb1: SMM does not respond, resetting usb1: <OHCI (generic) USB controller> on ohci1 usb1: USB revision 1.0 uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 3 ports with 3 removable, self powered ehciO: <EHCI (generic) USB 2.0 controller> mem 0xfbcff000-0xfbcff0ff irq 17 at d evice 18.2 on pci0 ehciO: Reserved 0x100 bytes for rid 0x10 type 3 at 0xfbcff000 ioapic0: routing intpin 17 (PCI IRQ 17) to vector 51 ehciO: [GIANT-LOCKED] ehciO: [ITHREAD] ehci0: Dropped interrupts workaround enabled Tried all available options on the boot loader, but in all cases kernel locked up at the same place. How-To-Repeat: 1. Put in the 7.0-RELEASE amd64 installation disc 1. 2. Select any option when prompted by the boot loader. Similar lock-ups occur with i386 installation disc also.
Please try to disable USB in BIOS. If that will drive you to a successful boot, please post us a verbose boot dmesg and `pciconf -lv' output. If you still experience problems, please try playing with ACPI settings and check your vendor for an updated BIOS version.
After disabling USB controller in BIOS, I was able to install FreeBSD. Once installed, I was not able to enable the network interface (Realtek RTL8168/8111). I saved the dmesg and pciconf information to text files, and then used Ubuntu live CD to mount the partition on which FreeBSD is installed to retrieve the text files. dmesg output: Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-RELEASE #0: Sun Feb 24 10:35:36 UTC 2008 root@driscoll.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80fc8000. Preloaded mfs_root "/boot/mfsroot" at 0xffffffff80fc81c0. Calibrating clock(s) ... i8254 clock: 1190233 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 2200903149 Hz CPU: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ (2200.90-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x60fb2 Stepping = 2 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x2001<SSE3,CX16> AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!> AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch> Cores per package: 2 L1 2MB data TLB: 8 entries, fully associative L1 2MB instruction TLB: 8 entries, fully associative L1 4KB data TLB: 32 entries, fully associative L1 4KB instruction TLB: 32 entries, fully associative L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L2 2MB unified TLB: 0 entries, disabled/not present L2 4KB data TLB: 512 entries, 4-way associative L2 4KB instruction TLB: 512 entries, 4-way associative L2 unified cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative usable memory = 1861701632 (1775 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009afff, 630784 bytes (154 pages) 0x00000000010c5000 - 0x000000006cad4fff, 1805713408 bytes (440848 pages) avail memory = 1795989504 (1712 MB) ACPI APIC Table: <041508 APIC1642> INTR: Adding local APIC 1 as a target FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 APIC: CPU 0 has ACPI ID 1 APIC: CPU 1 has ACPI ID 2 ACPI: RSDP @ 0x0xfb500/0x0024 (v 2 ACPIAM) ACPI: XSDT @ 0x0x6ffa0100/0x0054 (v 1 041508 XSDT1642 0x20080415 MSFT 0x00000097) ACPI: FACP @ 0x0x6ffa0290/0x00F4 (v 3 041508 FACP1642 0x20080415 MSFT 0x00000097) ACPI: DSDT @ 0x0x6ffa05c0/0x6DFD (v 1 A0896 A0896001 0x00000001 INTL 0x20051117) ACPI: FACS @ 0x0x6ffae000/0x0040 ACPI: APIC @ 0x0x6ffa0390/0x006C (v 1 041508 APIC1642 0x20080415 MSFT 0x00000097) ACPI: MCFG @ 0x0x6ffa0400/0x003C (v 1 041508 OEMMCFG 0x20080415 MSFT 0x00000097) ACPI: OEMB @ 0x0x6ffae040/0x0071 (v 1 041508 OEMB1642 0x20080415 MSFT 0x00000097) ACPI: HPET @ 0x0x6ffa73c0/0x0038 (v 1 041508 OEMHPET 0x20080415 MSFT 0x00000097) ACPI: SSDT @ 0x0x6ffa7400/0x0206 (v 1 A_M_I_ POWERNOW 0x00000001 AMD 0x00000001) MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000 ioapic0: Routing external 8259A's -> intpin 0 MADT: Interrupt override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 MADT: Interrupt override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: low ioapic0 <Version 2.1> irqs 0-23 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00010000 err: 0x0001000f pcm: 0x00010000 ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> wlan_amrr: <AMRR Transmit Rate Control Algorithm> wlan: <802.11 Link Layer> null: <null device, zero device> random: <entropy source, Software, Yarrow> nfslock: pseudo-device kbd: new array size 4 kbd1 at kbdmux0 mem: <memory> io: <I/O> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 10:34:18) acpi0: <041508 XSDT1642> on motherboard ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 acpi0: [MPSAFE] acpi0: [ITHREAD] acpi0: Power Button (fixed) AcpiOsDerivePciId: \\_SB_.PCI0.RS78.NB2_ -> bus 0 dev 0 func 0 AcpiOsDerivePciId: \\_SB_.PCI0.SATA.SACS -> bus 0 dev 17 func 0 acpi0: reservation of fee00000, 1000 (3) failed acpi0: reservation of ffb80000, 80000 (3) failed acpi0: reservation of fec10000, 20 (3) failed acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 6ff00000 (3) failed ACPI HPET table warning: Sequence is non-zero (2) ACPI timer: 1/2 1/2 0/5 1/2 0/3 1/2 1/2 1/2 1/2 1/2 -> 8 Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 pci_link0: Index IRQ Rtd Ref IRQs Initial Probe 0 10 N 0 4 7 10 11 12 14 15 Validation 0 10 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link1: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 4 7 10 11 12 14 15 Validation 0 255 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link2: Index IRQ Rtd Ref IRQs Initial Probe 0 10 N 0 4 7 10 11 12 14 15 Validation 0 10 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link3: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 4 7 10 11 12 14 15 Validation 0 255 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link4: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 4 7 10 11 12 14 15 Validation 0 255 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link5: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 4 7 10 11 12 14 15 Validation 0 255 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link6: Index IRQ Rtd Ref IRQs Initial Probe 0 11 N 0 4 7 10 11 12 14 15 Validation 0 11 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link7: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 4 7 10 11 12 14 15 Validation 0 255 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 acpi_hpet0: vend: 0x4353 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route Timecounter "HPET" frequency 14318180 Hz quality 900 cpu0: <ACPI CPU> on acpi0 cpu0: switching to generic Cx mode acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_throttle0: P_CNT from P_BLK 0x810 powernow0: <PowerNow! K8> on cpu0 cpu1: <ACPI CPU> on acpi0 powernow1: <PowerNow! K8> on cpu1 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: domain=0, physical bus=0 found-> vendor=0x1022, dev=0x9600, revid=0x00 domain=0, bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1043, dev=0x9602, revid=0x00 domain=0, bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x1a (6500 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x9606, revid=0x00 domain=0, bus=0, slot=6, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 3 supports D0 D3 current D0 MSI supports 1 message pcib0: matched entry for 0.6.INTA pcib0: slot 6 INTA hardwired to IRQ 18 found-> vendor=0x1002, dev=0x4391, revid=0x00 domain=0, bus=0, slot=17, func=0 class=01-06-01, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x0230, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 4 messages, 64 bit map[10]: type I/O Port, range 32, base rxc000, size 3, enabled map[14]: type I/O Port, range 32, base rxb000, size 2, enabled map[18]: type I/O Port, range 32, base rxa000, size 3, enabled map[1c]: type I/O Port, range 32, base rx9000, size 2, enabled map[20]: type I/O Port, range 32, base rx8000, size 4, enabled map[24]: type Memory, range 32, base rxfbcff800, size 10, enabled pcib0: matched entry for 0.17.INTA pcib0: slot 17 INTA hardwired to IRQ 22 found-> vendor=0x1002, dev=0x4385, revid=0x3a domain=0, bus=0, slot=20, func=0 class=0c-05-00, hdrtype=0x00, mfdev=1 cmdreg=0x0403, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1002, dev=0x439c, revid=0x00 domain=0, bus=0, slot=20, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 MSI supports 2 messages map[20]: type I/O Port, range 32, base rxff00, size 4, enabled found-> vendor=0x1002, dev=0x4383, revid=0x00 domain=0, bus=0, slot=20, func=2 class=04-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0410, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type Memory, range 64, base rxfbcf8000, size 14, enabled pcib0: matched entry for 0.20.INTA pcib0: slot 20 INTA hardwired to IRQ 16 found-> vendor=0x1002, dev=0x439d, revid=0x00 domain=0, bus=0, slot=20, func=3 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1002, dev=0x4384, revid=0x00 domain=0, bus=0, slot=20, func=4 class=06-04-01, hdrtype=0x01, mfdev=1 cmdreg=0x0105, statreg=0x02a0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1100, revid=0x00 domain=0, bus=0, slot=24, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1101, revid=0x00 domain=0, bus=0, slot=24, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1102, revid=0x00 domain=0, bus=0, slot=24, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1103, revid=0x00 domain=0, bus=0, slot=24, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pcib1: domain 0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xd000-0xdfff pcib1: memory decode 0xfbd00000-0xfbefffff pcib1: prefetched decode 0xd0000000-0xdfffffff pci1: <ACPI PCI bus> on pcib1 pci1: domain=0, physical bus=1 found-> vendor=0x1002, dev=0x9610, revid=0x00 domain=0, bus=1, slot=5, func=0 class=03-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0107, statreg=0x4010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 3 supports D0 D1 D2 D3 current D0 MSI supports 1 message, 64 bit map[10]: type Prefetchable Memory, range 32, base rxd0000000, size 28, enabled pcib1: requested memory range 0xd0000000-0xdfffffff: good map[14]: type I/O Port, range 32, base rxd000, size 8, enabled pcib1: requested I/O range 0xd000-0xd0ff: in range map[18]: type Memory, range 32, base rxfbef0000, size 16, enabled pcib1: requested memory range 0xfbef0000-0xfbefffff: good map[24]: type Memory, range 32, base rxfbd00000, size 20, enabled pcib1: requested memory range 0xfbd00000-0xfbdfffff: good pcib1: matched entry for 1.5.INTA pcib1: slot 5 INTA hardwired to IRQ 18 vgapci0: <VGA-compatible display> port 0xd000-0xd0ff mem 0xd0000000-0xdfffffff,0xfbef0000-0xfbefffff,0xfbd00000-0xfbdfffff irq 18 at device 5.0 on pci1 pcib2: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0 pcib2: domain 0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xe000-0xefff pcib2: memory decode 0xfbf00000-0xfbffffff pcib2: prefetched decode 0xfaf00000-0xfaffffff pci2: <ACPI PCI bus> on pcib2 pci2: domain=0, physical bus=2 found-> vendor=0x10ec, dev=0x8168, revid=0x02 domain=0, bus=2, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 3 supports D0 D1 D2 D3 current D0 MSI supports 1 message, 64 bit MSI-X supports 2 messages in map 0x20 map[10]: type I/O Port, range 32, base rxe800, size 8, enabled pcib2: requested I/O range 0xe800-0xe8ff: in range map[18]: type Memory, range 64, base rxfbfff000, size 12, enabled pcib2: requested memory range 0xfbfff000-0xfbffffff: good map[20]: type Prefetchable Memory, range 64, base rxfaff0000, size 16, enabled pcib2: requested memory range 0xfaff0000-0xfaffffff: good pcib2: matched entry for 2.0.INTA pcib2: slot 0 INTA hardwired to IRQ 18 re0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xe800 pcib2: re0 requested I/O range 0xe800-0xe8ff: in range pcib2: re0 requested I/O range 0xe800-0xe8ff: in range pci2: <network, ethernet> at device 0.0 (no driver attached) atapci0: <ATI (ID=43911002) AHCI controller> port 0xc000-0xc007,0xb000-0xb003,0xa000-0xa007,0x9000-0x9003,0x8000-0x800f mem 0xfbcff800-0xfbcffbff irq 22 at device 17.0 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x8000 atapci0: Reserved 0x400 bytes for rid 0x24 type 3 at 0xfbcff800 ioapic0: routing intpin 22 (PCI IRQ 22) to vector 49 atapci0: [MPSAFE] atapci0: [ITHREAD] atapci0: AHCI Version 01.10 controller with 4 ports detected ata2: <ATA channel 0> on atapci0 ata2: SATA connect time=0ms ata2: SIGNATURE: 00000101 ata2: ahci_reset devices=0x1<ATA_MASTER> ata2: [MPSAFE] ata2: [ITHREAD] ata3: <ATA channel 1> on atapci0 ata3: SATA connect time=0ms ata3: SIGNATURE: eb140101 ata3: ahci_reset devices=0x4<ATAPI_MASTER> ata3: [MPSAFE] ata3: [ITHREAD] ata4: <ATA channel 2> on atapci0 ata4: SATA connect status=00000000 ata4: ahci_reset devices=0x0 ata4: [MPSAFE] ata4: [ITHREAD] ata5: <ATA channel 3> on atapci0 ata5: SATA connect status=00000000 ata5: ahci_reset devices=0x0 ata5: [MPSAFE] ata5: [ITHREAD] pci0: <serial bus, SMBus> at device 20.0 (no driver attached) atapci1: <ATI IXP700 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xff00 ata0: <ATA channel 0> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=7f ostat1=7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat1=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: reset tp2 stat0=ff stat1=ff devices=0x0 ioapic0: routing intpin 14 (ISA IRQ 14) to vector 50 ata0: [MPSAFE] ata0: [ITHREAD] pci0: <multimedia> at device 20.2 (no driver attached) isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pcib3: domain 0 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0xf000-0xfff pcib3: no prefetched decode pcib3: Subtractively decoded bridge. pci3: <ACPI PCI bus> on pcib3 pci3: domain=0, physical bus=3 acpi_button0: <Power Button> on acpi0 fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: ic_type 90 part_id 80 ioapic0: routing intpin 6 (ISA IRQ 6) to vector 51 fdc0: [FILTER] ppc0: using extended I/O port range ppc0: SPP ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 ioapic0: routing intpin 7 (ISA IRQ 7) to vector 52 ppbus0: [MPSAFE] ppbus0: [ITHREAD] plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ppc0: [GIANT-LOCKED] ppc0: [ITHREAD] atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 ioapic0: routing intpin 1 (ISA IRQ 1) to vector 53 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] psm0: unable to allocate IRQ sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0 0 0 0 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0 0 0 0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A ioapic0: routing intpin 4 (ISA IRQ 4) to vector 54 sio0: [FILTER] ahc_isa_probe 0: ioport 0xc00 alloc failed ex_isa_identify() atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0 0 0 0 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 isa_probe_children: probing PnP devices Device configuration finished. Reducing kern.maxvnodes 116414 -> 100000 procfs registered lapic: Divisor 2, Frequency 100041058 hz Timecounter "TSC" frequency 2200903149 Hz quality -100 Timecounters tick every 1.000 msec lo0: bpf attached hptrr: no controller detected. md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xffffffff80bc6c08 ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire ad4: 715404MB <SAMSUNG HD753LJ 1AA01107> at ata2-master SATA300 ad4: 1465149168 sectors [1453521C/16H/63S] 16 sectors/interrupt 1 depth queue GEOM: new disk ad4 ad4: Silicon Image check1 failed ad4: Adaptec check1 failed ad4: LSI (v3) check1 failed ad4: LSI (v2) check1 failed ad4: FreeBSD check1 failed ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire ata3: device_reset timeout=4770us acd0: <HL-DT-ST DVDRAM GH20NS10/EL01> DVDR drive at ata3 as master acd0: read 8268KB/s (8268KB/s) write 8269KB/s (8269KB/s), 2048KB buffer, SATA150 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: CD-R 120mm data disc ATA PseudoRAID loaded SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000 ioapic0: Assigning ISA IRQ 1 to local APIC 0 ioapic0: Assigning ISA IRQ 4 to local APIC 1 ioapic0: Assigning ISA IRQ 6 to local APIC 0 ioapic0: Assigning ISA IRQ 7 to local APIC 1 ioapic0: Assigning ISA IRQ 9 to local APIC 0 ioapic0: Assigning ISA IRQ 14 to local APIC 1 ioapic0: Assigning PCI IRQ 22 to local APIC 0 GEOM_LABEL: Label for provider acd0 is iso9660/FreeBSD_Install. Trying to mount root from ufs:/dev/md0 start_init: trying /sbin/init start_init: trying /sbin/oinit start_init: trying /sbin/init.bak start_init: trying /rescue/init start_init: trying /stand/sysinstall GEOM: Reconfigure ad4s1a, start 0 length 536870912 end 536870911 GEOM: Reconfigure ad4s1b, start 536870912 length 3723403264 end 4260274175 GEOM: Reconfigure ad4s1c, start 0 length 750153729024 end 750153729023 GEOM: Reconfigure ad4s1d, start 4260274176 length 2934964224 end 7195238399 GEOM: Reconfigure ad4s1e, start 7195238400 length 536870912 end 7732109311 GEOM: Reconfigure ad4s1f, start 7732109312 length 74242161664 end 81974270975 GEOM: Reconfigure ad4s1a, start 0 length 536870912 end 536870911 GEOM: Reconfigure ad4s1b, start 536870912 length 3723403264 end 4260274175 GEOM: Reconfigure ad4s1c, start 0 length 750153729024 end 750153729023 GEOM: Reconfigure ad4s1d, start 4260274176 length 2934964224 end 7195238399 GEOM: Reconfigure ad4s1e, start 7195238400 length 536870912 end 7732109311 GEOM: Reconfigure ad4s1f, start 7732109312 length 74242161664 end 81974270975 GEOM: Reconfigure ad4s1a, start 0 length 536870912 end 536870911 GEOM: Reconfigure ad4s1b, start 536870912 length 3723403264 end 4260274175 GEOM: Reconfigure ad4s1c, start 0 length 750153729024 end 750153729023 GEOM: Reconfigure ad4s1d, start 4260274176 length 2934964224 end 7195238399 GEOM: Reconfigure ad4s1e, start 7195238400 length 536870912 end 7732109311 GEOM: Reconfigure ad4s1f, start 7732109312 length 74242161664 end 81974270975 GEOM: Reconfigure ad4s1a, start 0 length 536870912 end 536870911 GEOM: Reconfigure ad4s1b, start 536870912 length 3723403264 end 4260274175 GEOM: Reconfigure ad4s1c, start 0 length 750153729024 end 750153729023 GEOM: Reconfigure ad4s1d, start 4260274176 length 2934964224 end 7195238399 GEOM: Reconfigure ad4s1e, start 7195238400 length 536870912 end 7732109311 GEOM: Reconfigure ad4s1f, start 7732109312 length 74242161664 end 81974270975 Waiting (max 60 seconds) for system process `vnlru' to stop...done Waiting (max 60 seconds) for system process `bufdaemon' to stop...done Waiting (max 60 seconds) for system process `syncer' to stop... Syncing disks, vnodes remaining...7 1 0 0 done All buffers synced. Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-RELEASE #0: Sun Feb 24 10:35:36 UTC 2008 root@driscoll.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80bc8000. Calibrating clock(s) ... i8254 clock: 1190236 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 2200897702 Hz CPU: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ (2200.90-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x60fb2 Stepping = 2 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x2001<SSE3,CX16> AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!> AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch> Cores per package: 2 L1 2MB data TLB: 8 entries, fully associative L1 2MB instruction TLB: 8 entries, fully associative L1 4KB data TLB: 32 entries, fully associative L1 4KB instruction TLB: 32 entries, fully associative L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L2 2MB unified TLB: 0 entries, disabled/not present L2 4KB data TLB: 512 entries, 4-way associative L2 4KB instruction TLB: 512 entries, 4-way associative L2 unified cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative usable memory = 1865895936 (1779 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009afff, 630784 bytes (154 pages) 0x0000000000cc5000 - 0x000000006cad4fff, 1809907712 bytes (441872 pages) avail memory = 1800175616 (1716 MB) ACPI APIC Table: <041508 APIC1642> INTR: Adding local APIC 1 as a target FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 APIC: CPU 0 has ACPI ID 1 APIC: CPU 1 has ACPI ID 2 ACPI: RSDP @ 0x0xfb500/0x0024 (v 2 ACPIAM) ACPI: XSDT @ 0x0x6ffa0100/0x0054 (v 1 041508 XSDT1642 0x20080415 MSFT 0x00000097) ACPI: FACP @ 0x0x6ffa0290/0x00F4 (v 3 041508 FACP1642 0x20080415 MSFT 0x00000097) ACPI: DSDT @ 0x0x6ffa05c0/0x6DFD (v 1 A0896 A0896001 0x00000001 INTL 0x20051117) ACPI: FACS @ 0x0x6ffae000/0x0040 ACPI: APIC @ 0x0x6ffa0390/0x006C (v 1 041508 APIC1642 0x20080415 MSFT 0x00000097) ACPI: MCFG @ 0x0x6ffa0400/0x003C (v 1 041508 OEMMCFG 0x20080415 MSFT 0x00000097) ACPI: OEMB @ 0x0x6ffae040/0x0071 (v 1 041508 OEMB1642 0x20080415 MSFT 0x00000097) ACPI: HPET @ 0x0x6ffa73c0/0x0038 (v 1 041508 OEMHPET 0x20080415 MSFT 0x00000097) ACPI: SSDT @ 0x0x6ffa7400/0x0206 (v 1 A_M_I_ POWERNOW 0x00000001 AMD 0x00000001) MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000 ioapic0: Routing external 8259A's -> intpin 0 MADT: Interrupt override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 MADT: Interrupt override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: low ioapic0 <Version 2.1> irqs 0-23 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00010000 err: 0x0001000f pcm: 0x00010000 ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> wlan_amrr: <AMRR Transmit Rate Control Algorithm> wlan: <802.11 Link Layer> null: <null device, zero device> random: <entropy source, Software, Yarrow> nfslock: pseudo-device kbd: new array size 4 kbd1 at kbdmux0 mem: <memory> io: <I/O> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 10:34:18) acpi0: <041508 XSDT1642> on motherboard ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 acpi0: [MPSAFE] acpi0: [ITHREAD] acpi0: Power Button (fixed) AcpiOsDerivePciId: \\_SB_.PCI0.RS78.NB2_ -> bus 0 dev 0 func 0 AcpiOsDerivePciId: \\_SB_.PCI0.SATA.SACS -> bus 0 dev 17 func 0 acpi0: reservation of fee00000, 1000 (3) failed acpi0: reservation of ffb80000, 80000 (3) failed acpi0: reservation of fec10000, 20 (3) failed acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 6ff00000 (3) failed ACPI HPET table warning: Sequence is non-zero (2) ACPI timer: 1/2 1/2 1/2 1/2 0/3 0/3 1/2 1/2 0/4 0/3 -> 6 Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 pci_link0: Index IRQ Rtd Ref IRQs Initial Probe 0 10 N 0 4 7 10 11 12 14 15 Validation 0 10 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link1: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 4 7 10 11 12 14 15 Validation 0 255 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link2: Index IRQ Rtd Ref IRQs Initial Probe 0 10 N 0 4 7 10 11 12 14 15 Validation 0 10 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link3: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 4 7 10 11 12 14 15 Validation 0 255 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link4: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 4 7 10 11 12 14 15 Validation 0 255 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link5: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 4 7 10 11 12 14 15 Validation 0 255 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link6: Index IRQ Rtd Ref IRQs Initial Probe 0 11 N 0 4 7 10 11 12 14 15 Validation 0 11 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 pci_link7: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 4 7 10 11 12 14 15 Validation 0 255 N 0 4 7 10 11 12 14 15 After Disable 0 255 N 0 4 7 10 11 12 14 15 acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 acpi_hpet0: vend: 0x4353 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route Timecounter "HPET" frequency 14318180 Hz quality 900 cpu0: <ACPI CPU> on acpi0 cpu0: switching to generic Cx mode acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_throttle0: P_CNT from P_BLK 0x810 powernow0: <PowerNow! K8> on cpu0 cpu1: <ACPI CPU> on acpi0 powernow1: <PowerNow! K8> on cpu1 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: domain=0, physical bus=0 found-> vendor=0x1022, dev=0x9600, revid=0x00 domain=0, bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1043, dev=0x9602, revid=0x00 domain=0, bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x1a (6500 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x9606, revid=0x00 domain=0, bus=0, slot=6, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 3 supports D0 D3 current D0 MSI supports 1 message pcib0: matched entry for 0.6.INTA pcib0: slot 6 INTA hardwired to IRQ 18 found-> vendor=0x1002, dev=0x4391, revid=0x00 domain=0, bus=0, slot=17, func=0 class=01-06-01, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x0230, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 4 messages, 64 bit map[10]: type I/O Port, range 32, base rxc000, size 3, enabled map[14]: type I/O Port, range 32, base rxb000, size 2, enabled map[18]: type I/O Port, range 32, base rxa000, size 3, enabled map[1c]: type I/O Port, range 32, base rx9000, size 2, enabled map[20]: type I/O Port, range 32, base rx8000, size 4, enabled map[24]: type Memory, range 32, base rxfbcff800, size 10, enabled pcib0: matched entry for 0.17.INTA pcib0: slot 17 INTA hardwired to IRQ 22 found-> vendor=0x1002, dev=0x4385, revid=0x3a domain=0, bus=0, slot=20, func=0 class=0c-05-00, hdrtype=0x00, mfdev=1 cmdreg=0x0403, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1002, dev=0x439c, revid=0x00 domain=0, bus=0, slot=20, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 MSI supports 2 messages map[20]: type I/O Port, range 32, base rxff00, size 4, enabled found-> vendor=0x1002, dev=0x4383, revid=0x00 domain=0, bus=0, slot=20, func=2 class=04-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0410, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type Memory, range 64, base rxfbcf8000, size 14, enabled pcib0: matched entry for 0.20.INTA pcib0: slot 20 INTA hardwired to IRQ 16 found-> vendor=0x1002, dev=0x439d, revid=0x00 domain=0, bus=0, slot=20, func=3 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1002, dev=0x4384, revid=0x00 domain=0, bus=0, slot=20, func=4 class=06-04-01, hdrtype=0x01, mfdev=1 cmdreg=0x0105, statreg=0x02a0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1100, revid=0x00 domain=0, bus=0, slot=24, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1101, revid=0x00 domain=0, bus=0, slot=24, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1102, revid=0x00 domain=0, bus=0, slot=24, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1103, revid=0x00 domain=0, bus=0, slot=24, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pcib1: domain 0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xd000-0xdfff pcib1: memory decode 0xfbd00000-0xfbefffff pcib1: prefetched decode 0xd0000000-0xdfffffff pci1: <ACPI PCI bus> on pcib1 pci1: domain=0, physical bus=1 found-> vendor=0x1002, dev=0x9610, revid=0x00 domain=0, bus=1, slot=5, func=0 class=03-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0107, statreg=0x4010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 3 supports D0 D1 D2 D3 current D0 MSI supports 1 message, 64 bit map[10]: type Prefetchable Memory, range 32, base rxd0000000, size 28, enabled pcib1: requested memory range 0xd0000000-0xdfffffff: good map[14]: type I/O Port, range 32, base rxd000, size 8, enabled pcib1: requested I/O range 0xd000-0xd0ff: in range map[18]: type Memory, range 32, base rxfbef0000, size 16, enabled pcib1: requested memory range 0xfbef0000-0xfbefffff: good map[24]: type Memory, range 32, base rxfbd00000, size 20, enabled pcib1: requested memory range 0xfbd00000-0xfbdfffff: good pcib1: matched entry for 1.5.INTA pcib1: slot 5 INTA hardwired to IRQ 18 vgapci0: <VGA-compatible display> port 0xd000-0xd0ff mem 0xd0000000-0xdfffffff,0xfbef0000-0xfbefffff,0xfbd00000-0xfbdfffff irq 18 at device 5.0 on pci1 pcib2: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0 pcib2: domain 0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xe000-0xefff pcib2: memory decode 0xfbf00000-0xfbffffff pcib2: prefetched decode 0xfaf00000-0xfaffffff pci2: <ACPI PCI bus> on pcib2 pci2: domain=0, physical bus=2 found-> vendor=0x10ec, dev=0x8168, revid=0x02 domain=0, bus=2, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 3 supports D0 D1 D2 D3 current D0 MSI supports 1 message, 64 bit MSI-X supports 2 messages in map 0x20 map[10]: type I/O Port, range 32, base rxe800, size 8, enabled pcib2: requested I/O range 0xe800-0xe8ff: in range map[18]: type Memory, range 64, base rxfbfff000, size 12, enabled pcib2: requested memory range 0xfbfff000-0xfbffffff: good map[20]: type Prefetchable Memory, range 64, base rxfaff0000, size 16, enabled pcib2: requested memory range 0xfaff0000-0xfaffffff: good pcib2: matched entry for 2.0.INTA pcib2: slot 0 INTA hardwired to IRQ 18 re0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xe800 pcib2: re0 requested I/O range 0xe800-0xe8ff: in range pcib2: re0 requested I/O range 0xe800-0xe8ff: in range pci2: <network, ethernet> at device 0.0 (no driver attached) atapci0: <ATI (ID=43911002) AHCI controller> port 0xc000-0xc007,0xb000-0xb003,0xa000-0xa007,0x9000-0x9003,0x8000-0x800f mem 0xfbcff800-0xfbcffbff irq 22 at device 17.0 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x8000 atapci0: Reserved 0x400 bytes for rid 0x24 type 3 at 0xfbcff800 ioapic0: routing intpin 22 (PCI IRQ 22) to vector 49 atapci0: [MPSAFE] atapci0: [ITHREAD] atapci0: AHCI Version 01.10 controller with 4 ports detected ata2: <ATA channel 0> on atapci0 ata2: SATA connect time=0ms ata2: SIGNATURE: 00000101 ata2: ahci_reset devices=0x1<ATA_MASTER> ata2: [MPSAFE] ata2: [ITHREAD] ata3: <ATA channel 1> on atapci0 ata3: SATA connect time=0ms ata3: SIGNATURE: eb140101 ata3: ahci_reset devices=0x4<ATAPI_MASTER> ata3: [MPSAFE] ata3: [ITHREAD] ata4: <ATA channel 2> on atapci0 ata4: SATA connect status=00000000 ata4: ahci_reset devices=0x0 ata4: [MPSAFE] ata4: [ITHREAD] ata5: <ATA channel 3> on atapci0 ata5: SATA connect status=00000000 ata5: ahci_reset devices=0x0 ata5: [MPSAFE] ata5: [ITHREAD] pci0: <serial bus, SMBus> at device 20.0 (no driver attached) atapci1: <ATI IXP700 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xff00 ata0: <ATA channel 0> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=7f ostat1=7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: stat1=0x7f err=0x7f lsb=0x7f msb=0x7f ata0: reset tp2 stat0=ff stat1=ff devices=0x0 ioapic0: routing intpin 14 (ISA IRQ 14) to vector 50 ata0: [MPSAFE] ata0: [ITHREAD] pci0: <multimedia> at device 20.2 (no driver attached) isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pcib3: domain 0 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0xf000-0xfff pcib3: no prefetched decode pcib3: Subtractively decoded bridge. pci3: <ACPI PCI bus> on pcib3 pci3: domain=0, physical bus=3 acpi_button0: <Power Button> on acpi0 fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: ic_type 90 part_id 80 ioapic0: routing intpin 6 (ISA IRQ 6) to vector 51 fdc0: [FILTER] ppc0: using extended I/O port range ppc0: SPP ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 ioapic0: routing intpin 7 (ISA IRQ 7) to vector 52 ppbus0: [MPSAFE] ppbus0: [ITHREAD] plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ppc0: [GIANT-LOCKED] ppc0: [ITHREAD] atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 ioapic0: routing intpin 1 (ISA IRQ 1) to vector 53 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] psm0: unable to allocate IRQ sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0 0 0 0 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0 0 0 0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A ioapic0: routing intpin 4 (ISA IRQ 4) to vector 54 sio0: [FILTER] ahc_isa_probe 0: ioport 0xc00 alloc failed ex_isa_identify() atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0 0 0 0 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 isa_probe_children: probing PnP devices Device configuration finished. Reducing kern.maxvnodes 116670 -> 100000 procfs registered lapic: Divisor 2, Frequency 100040813 hz Timecounter "TSC" frequency 2200897702 Hz quality -100 Timecounters tick every 1.000 msec lo0: bpf attached hptrr: no controller detected. ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire ad4: 715404MB <SAMSUNG HD753LJ 1AA01107> at ata2-master SATA300 ad4: 1465149168 sectors [1453521C/16H/63S] 16 sectors/interrupt 1 depth queue GEOM: new disk ad4 ad4: Silicon Image check1 failed ad4: Adaptec check1 failed ad4: LSI (v3) check1 failed ad4: LSI (v2) check1 failed ad4: FreeBSD check1 failed ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire ata3: device_reset timeout=1500us acd0: <HL-DT-ST DVDRAM GH20NS10/EL01> DVDR drive at ata3 as master acd0: read 8268KB/s (8268KB/s) write 8269KB/s (8269KB/s), 2048KB buffer, SATA150 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc ATA PseudoRAID loaded SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000 ioapic0: Assigning ISA IRQ 1 to local APIC 0 ioapic0: Assigning ISA IRQ 4 to local APIC 1 ioapic0: Assigning ISA IRQ 6 to local APIC 0 ioapic0: Assigning ISA IRQ 7 to local APIC 1 ioapic0: Assigning ISA IRQ 9 to local APIC 0 ioapic0: Assigning ISA IRQ 14 to local APIC 1 ioapic0: Assigning PCI IRQ 22 to local APIC 0 Trying to mount root from ufs:/dev/ad4s1a start_init: trying /sbin/init END of dmesg output pciconf -lv output: hostb0@pci0:0:0:0: class=0x060000 card=0x82f11043 chip=0x96001022 rev=0x00 hdr=0x00 vendor = 'Advanced Micro Devices (AMD)' class = bridge subclass = HOST-PCI pcib1@pci0:0:1:0: class=0x060400 card=0x82f11043 chip=0x96021043 rev=0x00 hdr=0x01 vendor = 'Asustek Computer Inc.' class = bridge subclass = PCI-PCI pcib2@pci0:0:6:0: class=0x060400 card=0x82f11043 chip=0x96061022 rev=0x00 hdr=0x01 vendor = 'Advanced Micro Devices (AMD)' class = bridge subclass = PCI-PCI atapci0@pci0:0:17:0: class=0x010601 card=0x82ef1043 chip=0x43911002 rev=0x00 hdr=0x00 vendor = 'ATI Technologies Inc' class = mass storage none0@pci0:0:20:0: class=0x0c0500 card=0x82ef1043 chip=0x43851002 rev=0x3a hdr=0x00 vendor = 'ATI Technologies Inc' device = 'IXP SB600 SMBUS Controller' class = serial bus subclass = SMBus atapci1@pci0:0:20:1: class=0x01018a card=0x82ef1043 chip=0x439c1002 rev=0x00 hdr=0x00 vendor = 'ATI Technologies Inc' class = mass storage subclass = ATA none1@pci0:0:20:2: class=0x040300 card=0x82301043 chip=0x43831002 rev=0x00 hdr=0x00 vendor = 'ATI Technologies Inc' device = 'IXP SB600 High Definition Audio Controller' class = multimedia isab0@pci0:0:20:3: class=0x060100 card=0x82ef1043 chip=0x439d1002 rev=0x00 hdr=0x00 vendor = 'ATI Technologies Inc' class = bridge subclass = PCI-ISA pcib3@pci0:0:20:4: class=0x060401 card=0x00000000 chip=0x43841002 rev=0x00 hdr=0x01 vendor = 'ATI Technologies Inc' device = 'IXP SB600 PCI to PCI Bridge' class = bridge subclass = PCI-PCI hostb1@pci0:0:24:0: class=0x060000 card=0x00000000 chip=0x11001022 rev=0x00 hdr=0x00 vendor = 'Advanced Micro Devices (AMD)' device = '(K8) Athlon 64/Opteron HyperTransport Technology Configuration' class = bridge subclass = HOST-PCI hostb2@pci0:0:24:1: class=0x060000 card=0x00000000 chip=0x11011022 rev=0x00 hdr=0x00 vendor = 'Advanced Micro Devices (AMD)' device = '(K8) Athlon 64/Opteron Address Map' class = bridge subclass = HOST-PCI hostb3@pci0:0:24:2: class=0x060000 card=0x00000000 chip=0x11021022 rev=0x00 hdr=0x00 vendor = 'Advanced Micro Devices (AMD)' device = '(K8) Athlon 64/Opteron DRAM Controller' class = bridge subclass = HOST-PCI hostb4@pci0:0:24:3: class=0x060000 card=0x00000000 chip=0x11031022 rev=0x00 hdr=0x00 vendor = 'Advanced Micro Devices (AMD)' device = '(K8) Athlon 64/Opteron Miscellaneous Control' class = bridge subclass = HOST-PCI vgapci0@pci0:1:5:0: class=0x030000 card=0x82f11043 chip=0x96101002 rev=0x00 hdr=0x00 vendor = 'ATI Technologies Inc' class = display subclass = VGA none2@pci0:2:0:0: class=0x020000 card=0x82c61043 chip=0x816810ec rev=0x02 hdr=0x00 vendor = 'Realtek Semiconductor' device = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC' class = network subclass = ethernet END of pciconf -lv output
Hoon Choi, to get to the point where your system is hanging while USB is turned on, we need a bit more dmesg output before the system is hanging. I understand disabling USB is a temporary workaround and not an acceptable solution. We just need to identify the source of the problem (it might be a conflict when USB is enabled). Please try enabling USB again, boot verbose and post us the output until it hangs. Also I'm wondering if you're able to disable the SATA-RAID functionality in BIOS (assuming you don't want to use it). If mirroring is a need for you, gmirror work better than the pseudo "hardware" mirror functionality of the SATA-controller. It's a bit lengthy but can you please post output (or a URL containing files) of `devinfo -uv` and `devinfo -rv`? For the network issue: What do you get if kldload'ing if_re? Volker
State Changed From-To: open->feedback Note that submitter has been asked for feedback.
Responsible Changed From-To: freebsd-bugs->vwe track
RAID was and is disabled in BIOS. I am guessing there isn't a way to turn it off completely so that it is not detected. The console output from booting with USB re-enabled w/ verbose logging seems identical to the one submitted at the creation of the ticket. I've tried kldload, and it did not enable networking for me. Outputs from `devinfo -uv` and `devinfo -rv` are also included. Thanks. BEGIN verbose boot w/ USB re-enabled console output usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: <ATI OHCI root hub. class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 3 ports with 3 removable, self powered ohci1: <OHCI (generic) USB controller> mem 0xfbcfd000-0xfbcfdfff irq 16 at devic e 18.1 on pci0 ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfbcfd000 ohci1: [GIANT-LOCKED] ohci1: [ITHREAD] usb1: OHCI version 1.0, legacy support usb1: SMM does not respond, resetting usb1: <OHCI (generic) USB controller> on ohci1 usb1: USB revision 1.0 uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 3 ports with 3 removable, self powered ehciO: <EHCI (generic) USB 2.0 controller> mem 0xfbcff000-0xfbcff0ff irq 17 at d evice 18.2 on pci0 ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xfbcff000 ioapic0: routing intpin 17 (PCI IRQ 17) to vector 51 ehci0: [GIANT-LOCKED] ehci0: [ITHREAD] ehci0: Dropped interrupts workaround enabled END verbose boot w/ USB re-enabled console output BEGIN `devinfo -uv` (w/ USB disabled) output Interrupt request lines: 0 (root0) 1 (atkbd0) 3 (root0) 4 (sio0) 5 (root0) 6 (fdc0) 7 (ppc0) 8 (root0) 9 (acpi0) 10-13 (root0) 14 (ata0) 15-21 (root0) 22 (atapci0) 23 (root0) DMA request lines: 0-1 (root0) 2 (fdc0) 3-7 (root0) I/O ports: 0x0-0xf (root0) 0x10-0x1f (acpi0) 0x20-0x21 (root0) 0x22-0x3f (acpi0) 0x40-0x5f (root0) 0x60 (atkbdc0) 0x61 (root0) 0x62-0x63 (acpi0) 0x64 (atkbdc0) 0x65-0x6f (acpi0) 0x70-0x71 (root0) 0x72-0x7f (acpi0) 0x80 (acpi0) 0x81-0x83 (root0) 0x84-0x86 (acpi0) 0x87 (root0) 0x88 (acpi0) 0x89-0x8b (root0) 0x8c-0x8e (acpi0) 0x8f (root0) 0x90-0x9f (acpi0) 0xa0-0xa1 (root0) 0xa2-0xbf (acpi0) 0xc0-0xdf (root0) 0xe0-0xef (acpi0) 0xf0-0x16f (root0) 0x170-0x177 (atapci1) 0x178-0x1ef (root0) 0x1f0-0x1f7 (atapci1) 0x1f8-0x22f (root0) 0x230-0x23f (acpi0) 0x240-0x28f (root0) 0x290-0x29f (acpi0) 0x2a0-0x375 (root0) 0x376 (atapci1) 0x377 (root0) 0x378-0x37f (ppc0) 0x380-0x3bf (root0) 0x3c0-0x3df (vga0) 0x3e0-0x3ef (root0) 0x3f0-0x3f5 (fdc0) 0x3f6 (atapci1) 0x3f7 (fdc0) 0x3f8-0x3ff (sio0) 0x400-0x40a (root0) 0x40b (acpi0) 0x40c-0x4cf (root0) 0x4d0-0x4d1 (acpi0) 0x4d2-0x4d5 (root0) 0x4d6 (acpi0) 0x4d7-0x7ff (root0) 0x800-0x89f (acpi0) 0x8a0-0x8ff (root0) 0x900-0x90f (acpi0) 0x910-0x91f (acpi0) 0x920-0xa1f (root0) 0xa20-0xa2f (acpi0) 0xa30-0xa3f (acpi0) 0xa40-0xaff (root0) 0xb00-0xb3f (acpi0) 0xb40-0xbff (root0) 0xc00-0xc01 (acpi0) 0xc02-0xc13 (root0) 0xc14 (acpi0) 0xc15-0xc4f (root0) 0xc50-0xc51 (acpi0) 0xc52 (acpi0) 0xc53-0xc6b (root0) 0xc6c (acpi0) 0xc6d-0xc6e (root0) 0xc6f (acpi0) 0xc70-0xccf (root0) 0xcd0-0xcd1 (acpi0) 0xcd2-0xcd3 (acpi0) 0xcd4-0xcd5 (acpi0) 0xcd6-0xcd7 (acpi0) 0xcd8-0xcdf (acpi0) 0xce0-0x7fff (root0) 0x8000-0x800f (atapci0) 0x8010-0x8fff (root0) 0x9000-0x9003 (atapci0) 0x9004-0x9fff (root0) 0xa000-0xa007 (atapci0) 0xa008-0xafff (root0) 0xb000-0xb003 (atapci0) 0xb004-0xbfff (root0) 0xc000-0xc007 (atapci0) 0xc008-0xcfff (root0) 0xd000-0xd0ff (vgapci0) 0xd100-0xfdff (root0) 0xfe00-0xfefe (acpi0) 0xfeff (root0) 0xff00-0xff0f (atapci1) 0xff10-0xffff (root0) I/O memory addresses: 0x0-0x9ebff (ram0) 0x9ec00-0x9ffff (root0) 0xa0000-0xbffff (vga0) 0xc0000-0xcffff (acpi0) 0xd0000-0xdffff (root0) 0xe0000-0xfffff (acpi0) 0x100000-0x6ff9ffff (ram0) 0x6ffa0000-0xcfffffff (root0) 0xd0000000-0xdfffffff (vgapci0) 0xe0000000-0xefffffff (acpi0) 0xf0000000-0xfafeffff (root0) 0xfaff0000-0xfaffffff ---- 0xfb000000-0xfbcf7fff (root0) 0xfbcf8000-0xfbcfbfff ---- 0xfbcfc000-0xfbcff7ff (root0) 0xfbcff800-0xfbcffbff (atapci0) 0xfbcffc00-0xfbcfffff (root0) 0xfbd00000-0xfbdfffff (vgapci0) 0xfbe00000-0xfbeeffff (root0) 0xfbef0000-0xfbefffff (vgapci0) 0xfbf00000-0xfbffefff (root0) 0xfbfff000-0xfbffffff ---- 0xfc000000-0xfebfffff (root0) 0xfec00000-0xffffffff (acpi0) 0x100000000-0xffffffffffffffff (root0) ACPI I/O ports: 0x10-0x1f (root0) 0x22-0x3f (root0) 0x62-0x63 (root0) 0x65-0x6f (root0) 0x72-0x80 (root0) 0x84-0x86 (root0) 0x88 (root0) 0x8c-0x8e (root0) 0x90-0x9f (root0) 0xa2-0xbf (root0) 0xe0-0xef (root0) 0x230-0x23f (root0) 0x290-0x29f (root0) 0x40b (root0) 0x4d0-0x4d1 (root0) 0x4d6 (root0) 0x800-0x807 (root0) 0x808-0x80b (acpi_timer0) 0x80c-0x80f (root0) 0x810-0x813 (acpi_throttle0) 0x814-0x89f (root0) 0x900-0x91f (root0) 0xa20-0xa3f (root0) 0xb00-0xb3f (root0) 0xc00-0xc01 (root0) 0xc14 (root0) 0xc50-0xc52 (root0) 0xc6c (root0) 0xc6f (root0) 0xcd0-0xcdf (root0) 0xfe00-0xfefe (root0) ACPI I/O memory addresses: 0xc0000-0xcffff (root0) 0xe0000-0xfffff (root0) 0xe0000000-0xefffffff (root0) 0xfec00000-0xfecfffff (root0) 0xfed00000-0xfed003ff (acpi_hpet0) 0xfed00400-0xffffffff (root0) END `devinfo -uv` (w/ USB disabled) output BEGIN `devinfo -rv` (w/ USB disabled) output nexus0 acpi0 Interrupt request lines: 9 I/O ports: 0x10-0x1f 0x22-0x3f 0x62-0x63 0x65-0x6f 0x72-0x7f 0x80 0x84-0x86 0x88 0x8c-0x8e 0x90-0x9f 0xa2-0xbf 0xe0-0xef 0x230-0x23f 0x290-0x29f 0x40b 0x4d0-0x4d1 0x4d6 0x800-0x89f 0x900-0x90f 0x910-0x91f 0xa20-0xa2f 0xa30-0xa3f 0xb00-0xb3f 0xc00-0xc01 0xc14 0xc50-0xc51 0xc52 0xc6c 0xc6f 0xcd0-0xcd1 0xcd2-0xcd3 0xcd4-0xcd5 0xcd6-0xcd7 0xcd8-0xcdf 0xfe00-0xfefe I/O memory addresses: 0xc0000-0xcffff 0xe0000-0xfffff 0xe0000000-0xefffffff 0xfec00000-0xffffffff cpu0 pnpinfo _HID=none _UID=0 at handle=\_PR_.P001 acpi_perf0 acpi_throttle0 ACPI I/O ports: 0x810-0x813 powernow0 cpufreq0 cpu1 pnpinfo _HID=none _UID=0 at handle=\_PR_.P002 acpi_perf1 powernow1 cpufreq1 unknown pnpinfo _HID=none _UID=0 at handle=\_PR_.P003 unknown pnpinfo _HID=none _UID=0 at handle=\_PR_.P004 unknown pnpinfo _HID=none _UID=0 at handle=\_PR_.CPU1 unknown pnpinfo _HID=none _UID=0 at handle=\_PR_.CPU2 unknown pnpinfo _HID=none _UID=0 at handle=\_PR_.CPU3 unknown pnpinfo _HID=none _UID=0 at handle=\_PR_.CPU4 pcib0 pnpinfo _HID=PNP0A03 _UID=0 at handle=\_SB_.PCI0 pci0 hostb0 pnpinfo vendor=0x1022 device=0x9600 subvendor=0x1043 subdevice=0x82f1 class=0x060000 at slot=0 function=0 handle=\_SB_.PCI0.RS78 pcib1 pnpinfo vendor=0x1043 device=0x9602 subvendor=0x1043 subdevice=0x82f1 class=0x060400 at slot=1 function=0 handle=\_SB_.PCI0.P0P1 pci1 vgapci0 pnpinfo vendor=0x1002 device=0x9610 subvendor=0x1043 subdevice=0x82f1 class=0x030000 at slot=5 function=0 I/O ports: 0xd000-0xd0ff I/O memory addresses: 0xd0000000-0xdfffffff 0xfbd00000-0xfbdfffff 0xfbef0000-0xfbefffff drm0 pcib2 pnpinfo vendor=0x1022 device=0x9606 subvendor=0x1043 subdevice=0x82f1 class=0x060400 at slot=6 function=0 handle=\_SB_.PCI0.PCE6 pci2 unknown pnpinfo vendor=0x10ec device=0x8168 subvendor=0x1043 subdevice=0x82c6 class=0x020000 at slot=0 function=0 handle=\_SB_.PCI0.PCE6.RLAN I/O memory addresses: 0xfaff0000-0xfaffffff 0xfbfff000-0xfbffffff atapci0 pnpinfo vendor=0x1002 device=0x4390 subvendor=0x1043 subdevice=0x82ef class=0x01018f at slot=17 function=0 handle=\_SB_.PCI0.SATA Interrupt request lines: 22 I/O ports: 0x8000-0x800f 0x9000-0x9003 0xa000-0xa007 0xb000-0xb003 0xc000-0xc007 I/O memory addresses: 0xfbcff800-0xfbcffbff ata2 ad4 subdisk4 acd0 ata3 unknown pnpinfo vendor=0x1002 device=0x4385 subvendor=0x1043 subdevice=0x82ef class=0x0c0500 at slot=20 function=0 handle=\_SB_.PCI0.SMBS atapci1 pnpinfo vendor=0x1002 device=0x439c subvendor=0x1043 subdevice=0x82ef class=0x01018a at slot=20 function=1 handle=\_SB_.PCI0.IDEC I/O ports: 0x170-0x177 0x1f0-0x1f7 0x376 0x3f6 0xff00-0xff0f ata0 Interrupt request lines: 14 unknown pnpinfo vendor=0x1002 device=0x4383 subvendor=0x1043 subdevice=0x8230 class=0x040300 at slot=20 function=2 handle=\_SB_.PCI0.SBAZ I/O memory addresses: 0xfbcf8000-0xfbcfbfff isab0 pnpinfo vendor=0x1002 device=0x439d subvendor=0x1043 subdevice=0x82ef class=0x060100 at slot=20 function=3 handle=\_SB_.PCI0.SBRG isa0 sc0 sio1 sio2 sio3 vga0 I/O ports: 0x3c0-0x3df I/O memory addresses: 0xa0000-0xbffff pcib3 pnpinfo vendor=0x1002 device=0x4384 subvendor=0x0000 subdevice=0x0000 class=0x060401 at slot=20 function=4 handle=\_SB_.PCI0.P0PC pci3 hostb1 pnpinfo vendor=0x1022 device=0x1100 subvendor=0x0000 subdevice=0x0000 class=0x060000 at slot=24 function=0 hostb2 pnpinfo vendor=0x1022 device=0x1101 subvendor=0x0000 subdevice=0x0000 class=0x060000 at slot=24 function=1 hostb3 pnpinfo vendor=0x1022 device=0x1102 subvendor=0x0000 subdevice=0x0000 class=0x060000 at slot=24 function=2 hostb4 pnpinfo vendor=0x1022 device=0x1103 subvendor=0x0000 subdevice=0x0000 class=0x060000 at slot=24 function=3 acpi_sysresource0 pnpinfo _HID=PNP0C02 _UID=20 at handle=\_SB_.PCI0.RS78.BROD unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.PCE2 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.PCE3 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.PCE4 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.PCE5 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.PCE7 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.PCE9 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.PCEA unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.PCEB unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.PCEC unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.IDEC.PRID unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.IDEC.PRID.P_D0 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.IDEC.PRID.P_D1 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.IDEC.SECD unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.IDEC.SECD.S_D0 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.IDEC.SECD.S_D1 unknown pnpinfo _HID=PNP0000 _UID=0 at handle=\_SB_.PCI0.SBRG.PIC_ atdma0 pnpinfo _HID=PNP0200 _UID=0 at handle=\_SB_.PCI0.SBRG.DMAD attimer0 pnpinfo _HID=PNP0100 _UID=0 at handle=\_SB_.PCI0.SBRG.TMR_ attimer1 pnpinfo _HID=PNP0B00 _UID=0 at handle=\_SB_.PCI0.SBRG.RTC0 unknown pnpinfo _HID=PNP0800 _UID=0 at handle=\_SB_.PCI0.SBRG.SPKR fpupnp0 pnpinfo _HID=PNP0C04 _UID=0 at handle=\_SB_.PCI0.SBRG.COPR fdc0 pnpinfo _HID=PNP0700 _UID=0 at handle=\_SB_.PCI0.SBRG.FDC_ Interrupt request lines: 6 DMA request lines: 2 I/O ports: 0x3f0-0x3f5 0x3f7 fd0 ppc0 pnpinfo _HID=PNP0400 _UID=0 at handle=\_SB_.PCI0.SBRG.LPTE Interrupt request lines: 7 I/O ports: 0x378-0x37f ppbus0 plip0 lpt0 ppi0 unknown pnpinfo _HID=ATK0110 _UID=16843024 at handle=\_SB_.PCI0.SBRG.ASOC unknown pnpinfo _HID=PNP0103 _UID=0 at handle=\_SB_.PCI0.SBRG.HPET unknown pnpinfo _HID=PNP0F03 _UID=0 at handle=\_SB_.PCI0.SBRG.PS2M atkbdc0 pnpinfo _HID=PNP0303 _UID=0 at handle=\_SB_.PCI0.SBRG.PS2K I/O ports: 0x60 0x64 atkbd0 Interrupt request lines: 1 psm0 sio0 pnpinfo _HID=PNP0501 _UID=1 at handle=\_SB_.PCI0.SBRG.UAR1 Interrupt request lines: 4 I/O ports: 0x3f8-0x3ff acpi_sysresource1 pnpinfo _HID=PNP0C02 _UID=0 at handle=\_SB_.PCI0.SBRG.OMSC acpi_sysresource2 pnpinfo _HID=PNP0C02 _UID=16 at handle=\_SB_.PCI0.SBRG.RMSC acpi_sysresource3 pnpinfo _HID=PNP0C02 _UID=46 at handle=\_SB_.PCI0.SBRG.SIOR acpi_sysresource4 pnpinfo _HID=PNP0C02 _UID=17 at handle=\_SB_.PCI0.PCIE unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.UHC1 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.UHC2 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.UHC3 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.USB4 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.UHC5 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.UHC6 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.UHC7 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.SATA.PRID unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.SATA.PRID.P_D0 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.SATA.PRID.P_D1 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.SATA.SECD unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.SATA.SECD.S_D0 unknown pnpinfo _HID=none _UID=0 at handle=\_SB_.PCI0.SATA.SECD.S_D1 acpi_sysresource5 pnpinfo _HID=PNP0C01 _UID=1 at handle=\_SB_.RMEM acpi_button0 pnpinfo _HID=PNP0C0C _UID=170 at handle=\_SB_.PWRB pci_link0 pnpinfo _HID=PNP0C0F _UID=1 at handle=\_SB_.LNKA pci_link1 pnpinfo _HID=PNP0C0F _UID=2 at handle=\_SB_.LNKB pci_link2 pnpinfo _HID=PNP0C0F _UID=3 at handle=\_SB_.LNKC pci_link3 pnpinfo _HID=PNP0C0F _UID=4 at handle=\_SB_.LNKD pci_link4 pnpinfo _HID=PNP0C0F _UID=5 at handle=\_SB_.LNKE pci_link5 pnpinfo _HID=PNP0C0F _UID=2 at handle=\_SB_.LNKF pci_link6 pnpinfo _HID=PNP0C0F _UID=3 at handle=\_SB_.LNKG pci_link7 pnpinfo _HID=PNP0C0F _UID=4 at handle=\_SB_.LNKH acpi_timer0 pnpinfo unknown at unknown ACPI I/O ports: 0x808-0x80b acpi_hpet0 pnpinfo unknown at unknown ACPI I/O memory addresses: 0xfed00000-0xfed003ff apic0 legacy0 ram0 I/O memory addresses: 0x0-0x9ebff 0x100000-0x6ff9ffff END `devinfo -rv` (w/ USB disabled) output BEGIN `kldload -v if_re` (w/ USB disabled) output module_register: module re/miibus already exists! Module re/miibus failed to register: 17 module_register: module cardbus/re already exists! Module cardbus/re failed to register: 17 module_register: module pci/re already exitsts! Module pci/re failed to register: 17 kldload: can't load if_re: File exists END `kldload -v if_re` (w/ USB disabled) output
For bugs matching the following criteria: Status: In Progress Changed: (is less than) 2014-06-01 Reset to default assignee and clear in-progress tags. Mail being skipped
^Triage: I'm sorry that this PR did not get addressed in a timely fashion. By now, the version that it was created against is long out of suppoprt. Please re-open if it is still a problem on a supported version.