Realtek 8110SC with device ID 0x814910ec is not detected by FreeBSD 7.1. Most of New Mini-ITX boards are based on this chip. Here is a photo of the chips : Here is a photo of the daughterboard : http://i663.photobucket.com/albums/uu359/asgari/SANY0321-Low.jpg pciconf -lv output : hostb0@pci0:0:0:0: class=0x060000 card=0x27708086 chip=0x27708086 rev=0x02 hdr=0x00 class = bridge subclass = HOST-PCI vgapci0@pci0:0:2:0: class=0x030000 card=0x27728086 chip=0x27728086 rev=0x02 hdr=0x00 class = display subclass = VGA none0@pci0:0:27:0: class=0x040300 card=0xa62516f3 chip=0x27d88086 rev=0x01 hdr=0x00 class = multimedia pcib1@pci0:0:28:0: class=0x060400 card=0x27d08086 chip=0x27d08086 rev=0x01 hdr=0x01 class = bridge subclass = PCI-PCI uhci0@pci0:0:29:0: class=0x0c0300 card=0x27c88086 chip=0x27c88086 rev=0x01 hdr=0x00 class = serial bus subclass = USB uhci1@pci0:0:29:1: class=0x0c0300 card=0x27c98086 chip=0x27c98086 rev=0x01 hdr=0x00 class = serial bus subclass = USB uhci2@pci0:0:29:2: class=0x0c0300 card=0x27ca8086 chip=0x27ca8086 rev=0x01 hdr=0x00 class = serial bus subclass = USB uhci3@pci0:0:29:3: class=0x0c0300 card=0x27cb8086 chip=0x27cb8086 rev=0x01 hdr=0x00 class = serial bus subclass = USB ehci0@pci0:0:29:7: class=0x0c0320 card=0x27cc8086 chip=0x27cc8086 rev=0x01 hdr=0x00 class = serial bus subclass = USB pcib2@pci0:0:30:0: class=0x060401 card=0x244e8086 chip=0x244e8086 rev=0xe1 hdr=0x01 class = bridge subclass = PCI-PCI isab0@pci0:0:31:0: class=0x060100 card=0x27b88086 chip=0x27b88086 rev=0x01 hdr=0x00 class = bridge subclass = PCI-ISA atapci0@pci0:0:31:2: class=0x010180 card=0x27c08086 chip=0x27c08086 rev=0x01 hdr=0x00 class = mass storage subclass = ATA none1@pci0:0:31:3: class=0x0c0500 card=0x27da8086 chip=0x27da8086 rev=0x01 hdr=0x00 class = serial bus subclass = SMBus re0@pci0:1:0:0: class=0x020000 card=0x816810ec chip=0x816810ec rev=0x02 hdr=0x00 class = network subclass = ethernet none2@pci0:2:4:0: class=0x020000 card=0x10cc16f3 chip=0x814910ec rev=0x10 hdr=0x00 class = network subclass = ethernet none3@pci0:2:6:0: class=0x020000 card=0x10cc16f3 chip=0x814910ec rev=0x10 hdr=0x00 class = network subclass = ethernet none4@pci0:2:7:0: class=0x020000 card=0x10cc16f3 chip=0x814910ec rev=0x10 hdr=0x00 class = network subclass = ethernet DMESG output : Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.1-RELEASE-p5 #0: Wed Apr 22 15:35:36 EDT 2009 sullrich@RELENG_1_2-snapshots.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.7 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Atom(TM) CPU 330 @ 1.60GHz (1601.59-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x106c2 Stepping = 2 Features=0xbfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x40e31d<SSE3,DTES64,MON,DS_CPL,TM2,SSSE3,CX16,xTPR,PDCM,<b22>> AMD Features=0x20000000<LM> AMD Features2=0x1<LAHF> Logical CPUs per core: 4 real memory = 2137587712 (2038 MB) avail memory = 2081943552 (1985 MB) ACPI APIC Table: <IntelR AWRDACPI> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP): APIC ID: 3 ioapic0: Changing APIC ID to 4 ioapic0 <Version 2.0> irqs 0-23 on motherboard wlan: mac acl policy registered kbd1 at kbdmux0 cryptosoft0: <software crypto> on motherboard acpi0: <IntelR AWRDACPI> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 7f5e0000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 vgapci0: <VGA-compatible display> port 0xff00-0xff07 mem 0xfdf00000-0xfdf7ffff,0xd0000000-0xdfffffff,0xfdf80000-0xfdfbffff irq 16 at device 2.0 on pci0 agp0: <Intel 82945G (945G GMCH) SVGA controller> on vgapci0 agp0: detected 7932k stolen memory agp0: aperture size is 256M pci0: <multimedia> at device 27.0 (no driver attached) pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 pci1: <ACPI PCI bus> on pcib1 re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8111B/8111C/8111CP PCIe Gigabit Ethernet> port 0xde00-0xdeff mem 0xfddff000-0xfddfffff,0xfdef0000-0xfdefffff irq 16 at device 0.0 on pci1 re0: Using 1 MSI messages re0: Chip rev. 0x3c000000 re0: MAC rev. 0x00400000 miibus0: <MII bus> on re0 rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0 rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto re0: Ethernet address: 00:30:18:ab:4a:d8 re0: [FILTER] uhci0: <UHCI (generic) USB controller> port 0xfe00-0xfe1f irq 23 at device 29.0 on pci0 uhci0: [GIANT-LOCKED] uhci0: [ITHREAD] usb0: <UHCI (generic) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: <UHCI (generic) USB controller> port 0xfd00-0xfd1f irq 19 at device 29.1 on pci0 uhci1: [GIANT-LOCKED] uhci1: [ITHREAD] usb1: <UHCI (generic) USB controller> on uhci1 usb1: USB revision 1.0 uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 2 ports with 2 removable, self powered uhci2: <UHCI (generic) USB controller> port 0xfc00-0xfc1f irq 18 at device 29.2 on pci0 uhci2: [GIANT-LOCKED] uhci2: [ITHREAD] usb2: <UHCI (generic) USB controller> on uhci2 usb2: USB revision 1.0 uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2 uhub2: 2 ports with 2 removable, self powered uhci3: <UHCI (generic) USB controller> port 0xfb00-0xfb1f irq 16 at device 29.3 on pci0 uhci3: [GIANT-LOCKED] uhci3: [ITHREAD] usb3: <UHCI (generic) USB controller> on uhci3 usb3: USB revision 1.0 uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3 uhub3: 2 ports with 2 removable, self powered ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xfdfff000-0xfdfff3ff irq 23 at device 29.7 on pci0 ehci0: [GIANT-LOCKED] ehci0: [ITHREAD] usb4: EHCI version 1.0 usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0 usb4: USB revision 2.0 uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4 uhub4: 8 ports with 8 removable, self powered pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci2: <ACPI PCI bus> on pcib2 pci2: <network, ethernet> at device 4.0 (no driver attached) pci2: <network, ethernet> at device 6.0 (no driver attached) pci2: <network, ethernet> at device 7.0 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH7 SATA300 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f at device 31.2 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] ata1: <ATA channel 1> on atapci0 ata1: [ITHREAD] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) acpi_tz0: <Thermal Zone> on acpi0 speaker0: <PC speaker> port 0x61 on acpi0 cpu0: <ACPI CPU> on acpi0 p4tcc0: <CPU Frequency Thermal Control> on cpu0 cpu1: <ACPI CPU> on acpi0 p4tcc1: <CPU Frequency Thermal Control> on cpu1 cpu2: <ACPI CPU> on acpi0 p4tcc2: <CPU Frequency Thermal Control> on cpu2 cpu3: <ACPI CPU> on acpi0 p4tcc3: <CPU Frequency Thermal Control> on cpu3 pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xcc000-0xccfff pnpid ORM0000 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] ppc0: parallel port not found. sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding sio0: [FILTER] sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 rue0: <Linksys Linksys USB LAN Adapter, class 0/0, rev 1.10/1.00, addr 2> on uhub0 miibus1: <MII bus> on rue0 ruephy0: <RealTek RTL8150 internal media interface> PHY 0 on miibus1 ruephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rue0: WARNING: using obsoleted if_watchdog interface rue0: WARNING: using obsoleted IFF_NEEDSGIANT flag rue0: Ethernet address: 00:1a:70:90:a0:6d rue1: <Linksys Linksys USB LAN Adapter, class 0/0, rev 1.10/1.00, addr 2> on uhub1 miibus2: <MII bus> on rue1 ruephy1: <RealTek RTL8150 internal media interface> PHY 0 on miibus2 ruephy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rue1: WARNING: using obsoleted if_watchdog interface rue1: WARNING: using obsoleted IFF_NEEDSGIANT flag rue1: Ethernet address: 00:1a:70:90:a0:6c ukbd0: <NOVATEK USB Keyboard, class 0/0, rev 1.10/1.12, addr 3> on uhub1 kbd2 at ukbd0 uhid0: <NOVATEK USB Keyboard, class 0/0, rev 1.10/1.12, addr 3> on uhub1 Timecounters tick every 1.000 msec IPsec: Initialized Security Association Processing. ad0: 3919MB <SanDisk SDCFX3-004G HDX 4.32> at ata0-master UDMA66 SMP: AP CPU #1 Launched! SMP: AP CPU #2 Launched! SMP: AP CPU #3 Launched! Trying to mount root from ufs:/dev/ad0s1a Fix: I have no idea but someone has replied my post on pfsense forum : Well it looks like the only issue is that Jetway has changed the PCI IDs and that those IDs are not claimed by the re driver. It should be a trivial kernel patch to fix this, but I don't have the expertise or development environment set up to do it myself. How-To-Repeat: By using any NEW Jetway Board, Daughterboard, ... I've heard it's been used some other Mini-ITX and ITX boards like MSI, Tyan
State Changed From-To: open->feedback To submitter: can you please try the patch at http://people.freebsd.org/~gavin/PRs/134105.diff and see if that makes a difference? If you still do not get the extra interfaces, you should at least get extra lines in the dmesg, please supply them. Thanks!
Responsible Changed From-To: freebsd-i386->gavin Track
State Changed From-To: feedback->feedback To submitter: Are you still interested in this problem? If so, is there any chance you can test the patch? If you find it works, we can get it into the tree so that future releases support this card.
For bugs matching the following criteria: Status: In Progress Changed: (is less than) 2014-06-01 Reset to default assignee and clear in-progress tags. Mail being skipped