Dell Inspiron 530 panics at boot with the 8.1 kernel. The error message repeats to fast to read. I think it is "supervisor read data, page not present". Booting without ACPI did not change anything. After 20 tries I gave up and booted with kernel.old, which is at 8.0-p2. Here is a dmesg: Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-RELEASE-p2 #0: Mon Feb 15 02:37:50 GMT 2010 user@bawks:/usr/obj/usr/src/sys/CUSTOM Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz (2394.01-MHz K8-class CPU) Origin = "GenuineIntel" Id = 0x6fb Stepping = 11 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM> AMD Features=0x20100800<SYSCALL,NX,LM> AMD Features2=0x1<LAHF> TSC: P-state invariant real memory = 6442450944 (6144 MB) avail memory = 6171058176 (5885 MB) ACPI APIC Table: <DELL FX09 > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs FreeBSD/SMP: 1 package(s) x 4 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP): APIC ID: 3 ioapic0: Changing APIC ID to 4 ioapic0 <Version 2.0> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <DELL FX09 > on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, cfd90000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 device_attach: acpi_hpet0 attach returned 12 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <PCI-PCI bridge> irq 16 at device 1.0 on pci0 pci1: <PCI bus> on pcib1 vgapci0: <VGA-compatible display> port 0xcf00-0xcf7f mem 0xfa000000-0xfaffffff,0xd0000000-0xdfffffff,0xf8000000-0xf9ffffff irq 16 at device 0.0 on pci1 nvidia0: <GeForce 9600 GT> on vgapci0 vgapci0: child nvidia0 requested pci_enable_busmaster vgapci0: child nvidia0 requested pci_enable_io vgapci0: child nvidia0 requested pci_enable_io nvidia0: [ITHREAD] em0: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xff00-0xff1f mem 0xfdfc0000-0xfdfdffff,0xfdfff000-0xfdffffff irq 20 at device 25.0 on pci0 em0: Using MSI interrupt em0: [FILTER] em0: Ethernet address: 00:21:9b:04:79:a1 uhci0: <Intel 82801I (ICH9) USB controller> port 0xfe00-0xfe1f irq 16 at device 26.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x0f10 usbus0: <Intel 82801I (ICH9) USB controller> on uhci0 uhci1: <Intel 82801I (ICH9) USB controller> port 0xfd00-0xfd1f irq 21 at device 26.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x0f10 usbus1: <Intel 82801I (ICH9) USB controller> on uhci1 uhci2: <Intel 82801I (ICH9) USB controller> port 0xfc00-0xfc1f irq 19 at device 26.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x0f10 usbus2: <Intel 82801I (ICH9) USB controller> on uhci2 ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfdffe000-0xfdffe3ff irq 18 at device 26.7 on pci0 ehci0: [ITHREAD] usbus3: EHCI version 1.0 usbus3: <Intel 82801I (ICH9) USB 2.0 controller> on ehci0 hdac0: <Intel 82801I High Definition Audio Controller> mem 0xfdff4000-0xfdff7fff irq 22 at device 27.0 on pci0 hdac0: HDA Driver Revision: 20090624_0136 hdac0: [ITHREAD] uhci3: <Intel 82801I (ICH9) USB controller> port 0xfb00-0xfb1f irq 23 at device 29.0 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x003b usbus4: <Intel 82801I (ICH9) USB controller> on uhci3 uhci4: <Intel 82801I (ICH9) USB controller> port 0xfa00-0xfa1f irq 19 at device 29.1 on pci0 uhci4: [ITHREAD] uhci4: LegSup = 0x0010 usbus5: <Intel 82801I (ICH9) USB controller> on uhci4 uhci5: <Intel 82801I (ICH9) USB controller> port 0xf900-0xf91f irq 18 at device 29.2 on pci0 uhci5: [ITHREAD] uhci5: LegSup = 0x0010 usbus6: <Intel 82801I (ICH9) USB controller> on uhci5 ehci1: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfdffd000-0xfdffd3ff irq 23 at device 29.7 on pci0 ehci1: [ITHREAD] usbus7: EHCI version 1.0 usbus7: <Intel 82801I (ICH9) USB 2.0 controller> on ehci1 pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci2: <ACPI PCI bus> on pcib2 pci2: <simple comms> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH9 SATA300 controller> port 0xf800-0xf807,0xf700-0xf703,0xf600-0xf607,0xf500-0xf503,0xf400-0xf40f,0xf300-0xf30f irq 19 at device 31.2 on pci0 atapci0: [ITHREAD] ata2: <ATA channel 0> on atapci0 ata2: [ITHREAD] ata3: <ATA channel 1> on atapci0 ata3: [ITHREAD] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) atapci1: <Intel ICH9 SATA300 controller> port 0xf100-0xf107,0xf000-0xf003,0xef00-0xef07,0xee00-0xee03,0xed00-0xed0f,0xec00-0xec0f irq 19 at device 31.5 on pci0 atapci1: [ITHREAD] ata4: <ATA channel 0> on atapci1 ata4: [ITHREAD] ata5: <ATA channel 1> on atapci1 ata5: [ITHREAD] acpi_tz0: <Thermal Zone> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x73 on acpi0 cpu0: <ACPI CPU> on acpi0 est0: <Enhanced SpeedStep Frequency Control> on cpu0 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 925092506000925 device_attach: est0 attach returned 6 p4tcc0: <CPU Frequency Thermal Control> on cpu0 cpu1: <ACPI CPU> on acpi0 est1: <Enhanced SpeedStep Frequency Control> on cpu1 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 925092506000925 device_attach: est1 attach returned 6 p4tcc1: <CPU Frequency Thermal Control> on cpu1 cpu2: <ACPI CPU> on acpi0 est2: <Enhanced SpeedStep Frequency Control> on cpu2 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 925092506000925 device_attach: est2 attach returned 6 p4tcc2: <CPU Frequency Thermal Control> on cpu2 cpu3: <ACPI CPU> on acpi0 est3: <Enhanced SpeedStep Frequency Control> on cpu3 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 925092506000925 device_attach: est3 attach returned 6 p4tcc3: <CPU Frequency Thermal Control> on cpu3 acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 device_attach: acpi_hpet0 attach returned 12 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] ppc0: cannot reserve I/O port range Timecounters tick every 1.000 msec usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 ad4: 610480MB <WDC WD6400AAKS-75A7B0 01.03B01> at ata2-master SATA300 ugen0.1: <Intel> at usbus0 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <Intel> at usbus1 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen2.1: <Intel> at usbus2 uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <Intel> at usbus3 uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 ugen4.1: <Intel> at usbus4 uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 ugen5.1: <Intel> at usbus5 uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 ugen6.1: <Intel> at usbus6 uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6 ugen7.1: <Intel> at usbus7 uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered uhub5: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub3: 6 ports with 6 removable, self powered uhub7: 6 ports with 6 removable, self powered acd0: DVDR <PLDS DVD+/-RW DH-16A6S/YD11> at ata3-master SATA150 hdac0: HDA Codec #2: Realtek ALC888 pcm0: <HDA Realtek ALC888 PCM #0 Analog> at cad 2 nid 1 on hdac0 pcm1: <HDA Realtek ALC888 PCM #1 Analog> at cad 2 nid 1 on hdac0 SMP: AP CPU #1 Launched! SMP: AP CPU #3 Launched! SMP: AP CPU #2 Launched! Root mount waiting for: usbus7 usbus3 ugen7.2: <TEAC> at usbus7 umass0: <TEAC CA-200, class 0/0, rev 2.00/4.08, addr 2> on usbus7 umass0: SCSI over Bulk-Only; quirks = 0x0000 Root mount waiting for: usbus7 usbus3 umass0:0:0:-1: Attached to scbus0 Trying to mount root from ufs:/dev/ad4s1a ugen1.2: <Dell> at usbus1 ukbd0: <Dell Dell USB Keyboard, class 0/0, rev 1.10/3.06, addr 2> on usbus1 kbd2 at ukbd0 (probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 (probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error (probe0:umass-sim0:0:0:0): SCSI Status: Check Condition (probe0:umass-sim0:0:0:0): NOT READY asc:3a,0 (probe0:umass-sim0:0:0:0): Medium not present (probe0:umass-sim0:0:0:0): Unretryable error da0 at umass-sim0 bus 0 target 0 lun 0 da0: <TEAC USB HS-CF Card 4.08> Removable Direct Access SCSI-0 device da0: 40.000MB/s transfers da0: Attempt to query device size failed: NOT READY, Medium not present (probe0:umass-sim0:0:0:1): TEST UNIT READY. CDB: 0 20 0 0 0 0 (probe0:umass-sim0:0:0:1): CAM Status: SCSI Status Error (probe0:umass-sim0:0:0:1): SCSI Status: Check Condition (probe0:umass-sim0:0:0:1): NOT READY asc:3a,0 (probe0:umass-sim0:0:0:1): Medium not present (probe0:umass-sim0:0:0:1): Unretryable error da1 at umass-sim0 bus 0 target 0 lun 1 da1: <TEAC USB HS-xD/SM 4.08> Removable Direct Access SCSI-0 device da1: 40.000MB/s transfers da1: Attempt to query device size failed: NOT READY, Medium not present ugen2.2: <Logitech> at usbus2 ums0: <Logitech USB-PS/2 Optical Mouse, class 0/0, rev 2.00/20.00, addr 2> on usbus2 ums0: 3 buttons and [XYZ] coordinates ID=0 ugen1.3: <Wacom Co.,Ltd.> at usbus1 ums1: <Wacom Co.,Ltd. CTE-450, class 0/0, rev 2.00/1.13, addr 3> on usbus1 ums1: 3 buttons and [XYZ] coordinates ID=1 (probe0:umass-sim0:0:0:2): TEST UNIT READY. CDB: 0 40 0 0 0 0 (probe0:umass-sim0:0:0:2): CAM Status: SCSI Status Error (probe0:umass-sim0:0:0:2): SCSI Status: Check Condition (probe0:umass-sim0:0:0:2): NOT READY asc:3a,0 (probe0:umass-sim0:0:0:2): Medium not present (probe0:umass-sim0:0:0:2): Unretryable error da2 at umass-sim0 bus 0 target 0 lun 2 da2: <TEAC USB HS-MS Card 4.08> Removable Direct Access SCSI-0 device da2: 40.000MB/s transfers da2: Attempt to query device size failed: NOT READY, Medium not present KLD vboxdrv.ko: depends on kernel - not available or version mismatch linker_load_file: Unsupported file type KLD vboxnetflt.ko: depends on vboxdrv - not available or version mismatch linker_load_file: Unsupported file type (probe0:umass-sim0:0:0:3): TEST UNIT READY. CDB: 0 60 0 0 0 0 (probe0:umass-sim0:0:0:3): CAM Status: SCSI Status Error (probe0:umass-sim0:0:0:3): SCSI Status: Check Condition (probe0:umass-sim0:0:0:3): NOT READY asc:3a,0 (probe0:umass-sim0:0:0:3): Medium not present (probe0:umass-sim0:0:0:3): Unretryable error da3 at umass-sim0 bus 0 target 0 lun 3 da3: <TEAC USB HS-SD Card 4.08> Removable Direct Access SCSI-0 device da3: 40.000MB/s transfers da3: Attempt to query device size failed: NOT READY, Medium not present fuse4bsd: version 0.3.9-pre1, FUSE ABI 7.8 How-To-Repeat: Boot 8.1 on similar hardware.
Responsible Changed From-To: freebsd-bugs->freebsd-i386 reclassify.
I have the same machine and I ran 9-STABLE (amd64) on it. And since a month I run 10-STABLE (amd64) on it. It only panics on boot if you press a key before the kernel is loaded. Like what is mentioned here: http://lists.freebsd.org/pipermail/freebsd-current/2009-October/012602.html This still happens, but does not bother me. (And sounds like another issue anyways.) Is this issue still valid?
batch change: For bugs that match the following - Status Is In progress AND - Untouched since 2018-01-01. AND - Affects Base System OR Documentation DO: Reset to open status. Note: I did a quick pass but if you are getting this email it might be worthwhile to double check to see if this bug ought to be closed.
Keyword: crash – in lieu of summary line prefix: [panic] * bulk change for the keyword * summary lines may be edited manually (not in bulk). Keyword descriptions and search interface: <https://bugs.freebsd.org/bugzilla/describekeywords.cgi>
From 2014 comment 2: > Is this issue still valid? (In reply to RX from comment #0) I'm sorry that this bug was not investigated around the time of the report. If reproducible with an active branch of the OS, please make a new report. Thank you