After a day or more of uptime this happens: (System not very busy. general LA is 0.5-0.8, 14 jails) Fatal trap 9 general protection fault while in kernel mode cpuid = 1; acpi id = 01 instruction pointer = 0x20:0xffffffff8062fbd7 stack pointer = 0x28:0xffffff8078139550 frame pointer = 0x28:0xffffff80781395c0 code segment = base rx0. limit 0xfffff. type Qx1b DPL Q. pres 1. long 1. def3Z 0. gran 1 processor eflags = interrupt enabled. resume. IOPL = 0 current process = 98732 (postmap) trap number = 9 panic: general protection fault cpuid = 1 Uptime: 1d19h41m34s Cannot dump. Device not defined or unavailable. Automatic reboot in 15 seconds - press a key on the console to abort .. and it didnt reboots after 15 sec. only hard reset helps. If any more info requred to help solve this problem - just ask, and I will provide. DMESG:(just after reboot) Copyright (c) 1992-2010 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.1-RELEASE #3: Sat Jul 31 01:53:25 EEST 2010 root@inkiev.net:/usr/obj/usr/src/sys/GENERIC amd64 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz (2997.01-MHz K8-class CPU) Origin = "GenuineIntel" Id = 0x1067a Family = 6 Model = 17 Stepping = 10 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x408e3fd<SSE3,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,XSAVE> AMD Features=0x20100800<SYSCALL,NX,LM> AMD Features2=0x1<LAHF> TSC: P-state invariant real memory = 4294967296 (4096 MB) avail memory = 4105187328 (3915 MB) ACPI APIC Table: <A_M_I_ OEMAPIC > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 2 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0 <Version 2.0> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <A_M_I_ OEMRSDT> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, df600000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 ACPI Warning: Incorrect checksum in table [OEMB] - 0xEA, should be 0xDD (20100331/tbutils-354) cpu1: <ACPI CPU> on acpi0 acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 900 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 vgapci0: <VGA-compatible display> port 0xec00-0xec07 mem 0xfea00000-0xfea7ffff,0xe0000000-0xefffffff,0xfe900000-0xfe9fffff irq 16 at device 2.0 on pci0 agp0: <Intel G33 SVGA controller> on vgapci0 agp0: detected 7164k stolen memory agp0: aperture size is 256M vgapci1: <VGA-compatible display> mem 0xfea80000-0xfeafffff at device 2.1 on pci0 pci0: <multimedia, HDA> at device 27.0 (no driver attached) pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 pci2: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0 pci1: <ACPI PCI bus> on pcib2 age0: <Attansic Technology Corp, L1 Gigabit Ethernet> mem 0xfebc0000-0xfebfffff irq 17 at device 0.0 on pci1 age0: 1280 Tx FIFO, 2364 Rx FIFO age0: Using 1 MSI messages. age0: 4GB boundary crossed, switching to 32bit DMA addressing mode. miibus0: <MII bus> on age0 atphy0: <Atheros F1 10/100/1000 PHY> PHY 0 on miibus0 atphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto age0: Ethernet address: 00:1f:c6:a8:97:43 age0: [FILTER] uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0xe400-0xe41f irq 23 at device 29.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x2f00 usbus0: <Intel 82801G (ICH7) USB controller USB-A> on uhci0 uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0xe480-0xe49f irq 19 at device 29.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x2f00 usbus1: <Intel 82801G (ICH7) USB controller USB-B> on uhci1 uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0xe800-0xe81f irq 18 at device 29.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x2f00 usbus2: <Intel 82801G (ICH7) USB controller USB-C> on uhci2 uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0xe880-0xe89f irq 16 at device 29.3 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x2f00 usbus3: <Intel 82801G (ICH7) USB controller USB-D> on uhci3 ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xfe8f7c00-0xfe8f7fff irq 23 at device 29.7 on pci0 ehci0: [ITHREAD] usbus4: EHCI version 1.0 usbus4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0 pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci3: <ACPI PCI bus> on pcib3 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] atapci1: <Intel ICH7 SATA300 controller> port 0xe080-0xe087,0xe000-0xe003,0xdc00-0xdc07,0xd880-0xd883,0xd800-0xd80f irq 19 at device 31.2 on pci0 atapci1: [ITHREAD] ata2: <ATA channel 0> on atapci1 ata2: [ITHREAD] ata3: <ATA channel 1> on atapci1 ata3: [ITHREAD] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) acpi_button0: <Power Button> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: [FILTER] ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold ppc0: [ITHREAD] ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: [ITHREAD] lpt0: <Printer> on ppbus0 lpt0: [ITHREAD] lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 est0: <Enhanced SpeedStep Frequency Control> on cpu0 p4tcc0: <CPU Frequency Thermal Control> on cpu0 est1: <Enhanced SpeedStep Frequency Control> on cpu1 p4tcc1: <CPU Frequency Thermal Control> on cpu1 Timecounters tick every 1.000 msec usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 12Mbps Full Speed USB v1.0 usbus4: 480Mbps High Speed USB v2.0 ad4: 953869MB <Hitachi HDT721010SLA360 ST6OA3AA> at ata2-master UDMA100 SATA ugen0.1: <Intel> at usbus0 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <Intel> at usbus1 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen2.1: <Intel> at usbus2 uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <Intel> at usbus3 uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 ugen4.1: <Intel> at usbus4 uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4 ad5: 953869MB <SAMSUNG HD103UJ 1AA01118> at ata2-slave UDMA100 SATA ad6: 953869MB <Hitachi HDT721010SLA360 ST6OA3AA> at ata3-master UDMA100 SATA ad7: 953869MB <SAMSUNG HD103UJ 1AA01118> at ata3-slave UDMA100 SATA SMP: AP CPU #1 Launched! GEOM_MIRROR: Device mirror/gm-root launched (1/2). GEOM_MIRROR: Device gm-root: rebuilding provider ad4s1. GEOM_MIRROR: Device mirror/gm1 launched (1/2). GEOM_MIRROR: Device gm1: rebuilding provider ad5. Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub3: 2 ports with 2 removable, self powered Root mount waiting for: usbus4 Root mount waiting for: usbus4 uhub4: 8 ports with 8 removable, self powered Trying to mount root from ufs:/dev/mirror/gm-roota WARNING: / was not properly dismounted ugen1.2: <APC> at usbus1 ums0: <APC Mouse> on usbus1 ums0: 5 buttons and [XYZ] coordinates ID=0 ukbd0: <APC Keyboard> on usbus1 kbd2 at ukbd0 WARNING: / was not properly dismounted WARNING: /raid was not properly dismounted /raid: mount pending error: blocks 124 files 30 tun0: link state changed to UP
State Changed From-To: open->feedback Is this still a problem on recent FreeBSD versions?
For bugs matching the following criteria: Status: In Progress Changed: (is less than) 2014-06-01 Reset to default assignee and clear in-progress tags. Mail being skipped
Keyword: crash – in lieu of summary line prefix: [panic] * bulk change for the keyword * summary lines may be edited manually (not in bulk). Keyword descriptions and search interface: <https://bugs.freebsd.org/bugzilla/describekeywords.cgi>
^Triage: I'm sorry that this PR did not get addressed in a timely fashion. By now, the version that it was created against is long out of support. Please re-open if it is still a problem on a supported version.