FreeBSD 8.2 installed using Fixit# environment on several HP ProLiant BL460c G1 servers with HP SmartArray mirror sometimes does not boot from ZFS pool. Installation done according to http://wiki.freebsd.org/RootOnZFS/GPTZFSBoot with swap volume located on ZFS. There are 2 disks configured on HP SmartArray as RAID1 array. Thus there is one logical device da0 and two GPT partitions: # gpart show => 34 143305853 da0 GPT (68G) 34 128 1 freebsd-boot (64K) 162 143305725 2 freebsd-zfs (68G) # dmesg ciss0: <HP Smart Array E200i> port 0x4000-0x40ff mem 0xfde80000-0xfdefffff,0xfde70000-0xfde77fff irq 18 at device 8.0 on pci11 ciss0: PERFORMANT Transport ciss0: got 2 MSI messages] ciss0: [ITHREAD] da0 at ciss0 bus 0 scbus0 target 0 lun 0 da0: <COMPAQ RAID 1(1VOLUME OK> Fixed Direct Access SCSI-5 device da0: 135.168MB/s transfers da0: Command Queueing enabled da0: 69973MB (143305920 512 byte sectors: 255H 32S/T 17562C) # diskinfo -v da0 da0 512 # sectorsize 73372631040 # mediasize in bytes (68G) 143305920 # mediasize in sectors 0 # stripesize 0 # stripeoffset 17562 # Cylinders according to firmware. 255 # Heads according to firmware. 32 # Sectors according to firmware. P688MQ0598 # Disk ident. # pciconf -lv ciss0@pci0:11:8:0: class=0x010400 card=0x3211103c chip=0x3238103c rev=0x00 hdr=0x00 vendor = 'Hewlett-Packard Company' device = 'Smart Array E200/E200i SAS/SATA Controller' class = mass storage subclass = RAID # zfs list NAME USED AVAIL REFER MOUNTPOINT zroot 12,0G 55,0G 548M legacy zroot/home 56K 55,0G 56K /home zroot/storage 21K 30,0G 21K /storage zroot/swap 10G 65,0G 16K - zroot/usr 1,31G 55,0G 760M /usr zroot/usr/obj 20K 55,0G 20K /usr/obj zroot/usr/ports 267M 55,0G 267M /usr/ports zroot/usr/ports/distfiles 20K 55,0G 20K /usr/ports/distfiles zroot/usr/ports/packages 21K 55,0G 21K /usr/ports/packages zroot/usr/src 311M 55,0G 311M /usr/src zroot/var 125M 55,0G 247K /var zroot/var/db 125M 55,0G 121M /var/db zroot/var/db/pkg 3,94M 55,0G 3,94M /var/db/pkg zroot/var/log 215K 55,0G 215K /var/log zroot/var/mail 20K 55,0G 20K /var/mail # md5 /boot/gptzfsboot MD5 (/boot/gptzfsboot) = fd31f87e1c8e2bb4fa06b89658c63d06 # zdb -uuu zroot Uberblock magic = 0000000000bab10c version = 15 txg = 20726 guid_sum = 3529677120116096247 timestamp = 1293618442 UTC = Wed Dec 29 12:27:22 2010 rootbp = [L0 DMU objset] 800L/200P DVA[0]=<0:1200ee400:200> DVA[1]=<0:3803ec200:200> DVA[2]=<0:5c0005c00:200> fletcher4 lzjb LE contiguous birth=20726 fill=245 cksum=c37f85b6c:4b1d45d93d8:eb0f06388e48:1f34f5d644dceb Sometimes, after high disk load (e.g. buildworld) followed by reboot we got: error 1 lba 32 error 1 lba 1 No ZFS pools located, can't boot But after some numbers of reboots we can normally boot... How-To-Repeat: 1. Install 8.2-RC1 amd64 according to http://wiki.freebsd.org/RootOnZFS/GPTZFSBoot 2. reboot 3. rebuild/install world && kernel 4. reboot
Responsible Changed From-To: freebsd-bugs->freebsd-fs Hard to tell if this is a ZFS problem or a controller problem, but take a guess.
Acknowledge flawed work zdb -uuu # zdb -uuu tank Assertion failed: (rwlp->rw_count == 0), file /usr/src/cddl/lib/libzpool/../../../cddl/contrib/opensolaris/lib/libzpool/common/kernel.c, line 203. ÐваÑийное завеÑÑение(core dumped) # uname -a FreeBSD mary-teresa.XXX.ua 9.0-CURRENT FreeBSD 9.0-CURRENT #0: Sun Aug 29 19:00:25 EEST 2010 vlad11@mary-teresa.XXX.ua:/usr/obj/usr/src/sys/mary-teresa.24 amd64 # zpool status pool: tank state: ONLINE scrub: scrub completed after 20h41m with 0 errors on Sun Jan 2 22:39:05 2011 config: NAME STATE READ WRITE CKSUM tank ONLINE 0 0 0 raidz2 ONLINE 0 0 0 ad8 ONLINE 0 0 0 ad10 ONLINE 0 0 0 ad12 ONLINE 0 0 0 ad14 ONLINE 0 0 0 ad16 ONLINE 0 0 0 ad18 ONLINE 0 0 0 224K repaired # zfs list NAME USED AVAIL REFER MOUNTPOINT tank 2,48T 185G 2,48T /tank # zdb tank version=14 name='tank' state=0 txg=5960112 pool_guid=17628573572433446879 hostid=2180312168 hostname='mary-teresa.XXX.ua' vdev_tree type='root' id=0 guid=17628573572433446879 children[0] type='raidz' id=0 guid=17179795338638175685 nparity=2 metaslab_array=14 metaslab_shift=35 ashift=9 asize=4500909195264 is_log=0 children[0] type='disk' id=0 guid=8139272885001209353 path='/dev/ad8' whole_disk=0 DTL=18 children[1] type='disk' id=1 guid=11968336865843447944 path='/dev/ad10' whole_disk=0 DTL=23 children[2] type='disk' id=2 guid=9145116577681738566 path='/dev/ad12' whole_disk=0 DTL=22 children[3] type='disk' id=3 guid=1210172854298467640 path='/dev/ad14' whole_disk=0 DTL=21 children[4] type='disk' id=4 guid=13774245294784048495 path='/dev/ad16' whole_disk=0 DTL=20 children[5] type='disk' id=5 guid=14124887767830680597 path='/dev/ad18' whole_disk=0 DTL=19 -- Vladislav V. Prodan VVP24-UANIC +38[067]4584408 +38[099]4060508 vlad11@jabber.ru
I see this too on two identical HP Proliant 320 DL G6 with 9-STABLE. The machine usually needs some nudging in the form of warm restarts to boot the operating system. =3D=3D bootloader output =3D=3D error 1 lba 32 error 1 lba 1 No ZFS pools located, can't boot =3D=3D bootloader output =3D=3D =3D=3D gpart show =3D=3D =3D> 34 488326973 da0 GPT (232G) 34 128 1 freebsd-boot (64k) 162 67108864 2 freebsd-swap (32G) 67109026 421217981 3 freebsd-zfs [bootme] (200G) =3D=3D gpart show =3D=3D Root is on a hardware-mirror provided by the machine's HPQ Smart Array P410i The other 6 drives are configured as JBOD with a raidz2 data pool (not shown here) =3D=3D zpool status rpool =3D=3D zpool status rpool pool: rpool state: ONLINE scan: scrub repaired 0 in 0h12m with 0 errors on Wed Nov 7 04:47:21 2012 config: NAME STATE READ WRITE CKSUM rpool ONLINE 0 0 0 da0p3 ONLINE 0 0 0 errors: No known data errors =3D=3D zpool status rpool =3D=3D =3D=3D zdb =3D=3D rpool: version: 28 name: 'rpool' state: 0 txg: 22695230816 pool_guid: 16981309850887562666 hostid: 1031366389 hostname: '...' vdev_children: 1 vdev_tree: type: 'root' id: 0 guid: 16981309850887562666 children[0]: type: 'disk' id: 0 guid: 6716485486554561877 path: '/dev/da0p3' phys_path: '/dev/da0p3' whole_disk: 0 metaslab_array: 23 metaslab_shift: 31 ashift: 9 asize: 215658790912 is_log: 0 DTL: 65 =3D=3D zdb =3D=3D =3D=3D dmesg =3D=3D Copyright (c) 1992-2012 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.1-PRERELEASE #3 r242394: Wed Oct 31 13:15:48 CET 2012 src@...:/usr/obj/usr/src/sys/ML350 amd64 CPU: Intel(R) Xeon(R) CPU E5504 @ 2.00GHz (2000.12-MHz K8-class = CPU) Origin =3D "GenuineIntel" Id =3D 0x106a5 Family =3D 0x6 Model =3D 0x1a= Stepping =3D 5 Features=3D0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PG= E,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=3D0x9ce3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,P= DCM,DCA,SSE4.1,SSE4.2,POPCNT> AMD Features=3D0x28100800<SYSCALL,NX,RDTSCP,LM> AMD Features2=3D0x1<LAHF> TSC: P-state invariant, performance statistics real memory =3D 6442450944 (6144 MB) avail memory =3D 6177263616 (5891 MB) Event timer "LAPIC" quality 400 ACPI APIC Table: <HP ProLiant> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs FreeBSD/SMP: 1 package(s) x 4 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 2 cpu2 (AP): APIC ID: 4 cpu3 (AP): APIC ID: 6 ACPI Warning: Invalid length for Pm1aControlBlock: 32, using default 16 (20= 110527/tbfadt-638) ACPI Warning: Invalid length for Pm2ControlBlock: 32, using default 8 (2011= 0527/tbfadt-638) ioapic1 <Version 2.0> irqs 24-47 on motherboard ioapic0 <Version 2.0> irqs 0-23 on motherboard kbd1 at kbdmux0 cryptosoft0: <software crypto> on motherboard acpi0: <HP ProLiant> on motherboard acpi0: Power Button (fixed) cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 cpu2: <ACPI CPU> on acpi0 cpu3: <ACPI CPU> on acpi0 attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 950 Event timer "HPET" frequency 14318180 Hz quality 450 Event timer "HPET1" frequency 14318180 Hz quality 440 Event timer "HPET2" frequency 14318180 Hz quality 440 Event timer "HPET3" frequency 14318180 Hz quality 440 atrtc0: <AT realtime clock> port 0x70-0x71 on acpi0 Event timer "RTC" frequency 32768 Hz quality 0 Timecounter "ACPI-fast" frequency 3579545 Hz quality 900 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x908-0x90b on acpi0 pcib0: <ACPI Host-PCI bridge> on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci4: <ACPI PCI bus> on pcib1 ciss0: <HP Smart Array P410i> port 0x4000-0x40ff mem 0xfb000000-0xfb3fffff,= 0xfaff0000-0xfaff0fff irq 28 at device 0.0 on pci4 ciss0: PERFORMANT Transport pcib2: <ACPI PCI-PCI bridge> at device 2.0 on pci0 pci23: <ACPI PCI bus> on pcib2 pcib3: <ACPI PCI-PCI bridge> at device 3.0 on pci0 pci5: <ACPI PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> at device 4.0 on pci0 pci8: <ACPI PCI bus> on pcib4 pcib5: <ACPI PCI-PCI bridge> at device 5.0 on pci0 pci11: <ACPI PCI bus> on pcib5 pcib6: <ACPI PCI-PCI bridge> at device 6.0 on pci0 pci24: <ACPI PCI bus> on pcib6 pcib7: <ACPI PCI-PCI bridge> at device 7.0 on pci0 pci14: <ACPI PCI bus> on pcib7 ciss1: <HP Smart Array P212> port 0x5000-0x50ff mem 0xfb800000-0xfbbfffff,0= xfb7f0000-0xfb7f0fff irq 30 at device 0.0 on pci14 ciss1: PERFORMANT Transport pcib8: <ACPI PCI-PCI bridge> at device 8.0 on pci0 pci25: <ACPI PCI bus> on pcib8 pcib9: <ACPI PCI-PCI bridge> at device 9.0 on pci0 pci17: <ACPI PCI bus> on pcib9 pcib10: <ACPI PCI-PCI bridge> at device 10.0 on pci0 pci20: <ACPI PCI bus> on pcib10 mpt0: <LSILogic SAS/SATA Adapter> port 0x6000-0x60ff mem 0xfbff0000-0xfbff3= fff,0xfbfe0000-0xfbfeffff irq 33 at device 0.0 on pci20 mpt0: MPI Version=3D1.5.16.0 mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 ) mpt0: 0 Active Volumes (2 Max) mpt0: 0 Hidden Drive Members (10 Max) pci0: <base peripheral, interrupt controller> at device 20.0 (no driver att= ached) pci0: <base peripheral, interrupt controller> at device 20.1 (no driver att= ached) pci0: <base peripheral, interrupt controller> at device 20.2 (no driver att= ached) pcib11: <ACPI PCI-PCI bridge> at device 28.0 on pci0 pci2: <ACPI PCI bus> on pcib11 pcib12: <ACPI PCI-PCI bridge> at device 0.0 on pci2 pci3: <ACPI PCI bus> on pcib12 bge0: <HP NC326i Dual Port PCI-E Gigabit Adapter, ASIC rev. 0x009003> mem 0= xfaef0000-0xfaefffff,0xfaee0000-0xfaeeffff irq 16 at device 4.0 on pci3 bge0: CHIP ID 0x00009003; ASIC REV 0x09; CHIP REV 0x90; PCI-X 133 MHz miibus0: <MII bus> on bge0 brgphy0: <BCM5714 1000BASE-T media interface> PHY 1 on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000ba= seT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow bge0: Ethernet address: 00:25:b3:ad:a5:8c bge1: <HP NC326i Dual Port PCI-E Gigabit Adapter, ASIC rev. 0x009003> mem 0= xfaed0000-0xfaedffff,0xfaec0000-0xfaecffff irq 17 at device 4.1 on pci3 bge1: CHIP ID 0x00009003; ASIC REV 0x09; CHIP REV 0x90; PCI-X 133 MHz miibus1: <MII bus> on bge1 brgphy1: <BCM5714 1000BASE-T media interface> PHY 1 on miibus1 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000ba= seT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow bge1: Ethernet address: 00:25:b3:ad:a5:8d uhci0: <Intel 82801JI (ICH10) USB controller USB-A> port 0x1000-0x101f irq = 20 at device 29.0 on pci0 usbus0 on uhci0 uhci1: <Intel 82801JI (ICH10) USB controller USB-B> port 0x1020-0x103f irq = 23 at device 29.1 on pci0 usbus1 on uhci1 uhci2: <Intel 82801JI (ICH10) USB controller USB-C> port 0x1040-0x105f irq = 22 at device 29.2 on pci0 usbus2 on uhci2 uhci3: <Intel 82801JI (ICH10) USB controller USB-F> port 0x1060-0x107f irq = 23 at device 29.3 on pci0 usbus3 on uhci3 ehci0: <Intel 82801JI (ICH10) USB 2.0 controller USB-A> mem 0xfabf0000-0xfa= bf03ff irq 20 at device 29.7 on pci0 usbus4: EHCI version 1.0 usbus4 on ehci0 pcib13: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci1: <ACPI PCI bus> on pcib13 vgapci0: <VGA-compatible display> port 0x3000-0x30ff mem 0xf0000000-0xf7fff= fff,0xfadf0000-0xfadfffff irq 23 at device 3.0 on pci1 pci1: <base peripheral> at device 4.0 (no driver attached) pci1: <base peripheral> at device 4.2 (no driver attached) uhci4: <UHCI (generic) USB controller> port 0x3800-0x381f irq 22 at device = 4.4 on pci1 usbus5 on uhci4 ipmi0: <IPMI System Interface> mem 0xfacf0000-0xfacf00ff irq 21 at device 4= =2E6 on pci1 ipmi0: using KSC interface isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH10 SATA300 controller> port 0x10c0-0x10c7,0x10c8-0x10cb,= 0x10d0-0x10d7,0x10d8-0x10db,0x10e0-0x10ef,0x10f0-0x10ff irq 17 at device 31= =2E5 on pci0 ata2: <ATA channel> at channel 0 on atapci0 ata3: <ATA channel> at channel 1 on atapci0 acpi_tz0: <Thermal Zone> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] qpi0: <QPI system bus> on motherboard ipmi1: <IPMI System Interface> on isa0 device_attach: ipmi1 attach returned 16 ipmi1: <IPMI System Interface> on isa0 device_attach: ipmi1 attach returned 16 orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=3D0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 coretemp0: <CPU On-Die Thermal Sensors> on cpu0 est0: <Enhanced SpeedStep Frequency Control> on cpu0 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr f device_attach: est0 attach returned 6 p4tcc0: <CPU Frequency Thermal Control> on cpu0 coretemp1: <CPU On-Die Thermal Sensors> on cpu1 est1: <Enhanced SpeedStep Frequency Control> on cpu1 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr f device_attach: est1 attach returned 6 p4tcc1: <CPU Frequency Thermal Control> on cpu1 coretemp2: <CPU On-Die Thermal Sensors> on cpu2 est2: <Enhanced SpeedStep Frequency Control> on cpu2 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr f device_attach: est2 attach returned 6 p4tcc2: <CPU Frequency Thermal Control> on cpu2 coretemp3: <CPU On-Die Thermal Sensors> on cpu3 est3: <Enhanced SpeedStep Frequency Control> on cpu3 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr f device_attach: est3 attach returned 6 p4tcc3: <CPU Frequency Thermal Control> on cpu3 ZFS filesystem version 5 ZFS storage pool version 28 Timecounters tick every 10.000 msec usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 12Mbps Full Speed USB v1.0 usbus4: 480Mbps High Speed USB v2.0 usbus5: 12Mbps Full Speed USB v1.0 ugen0.1: <Intel> at usbus0 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <Intel> at usbus1 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 (probe0:ciss0:0:0:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0=20 (probe0:ciss0:0:0:0): CAM status: SCSI Status Error (probe0:ciss0:0:0:0): SCSI status: Check Condition (probe0:ciss0:0:0:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid command= operation code) (probe0:ciss0:0:0:0): Error 22, Unretryable error ugen2.1: <Intel> at usbus2 uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <Intel> at usbus3 uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 (probe1:ciss0:0:1:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0=20 (probe1:ciss0:0:1:0): CAM status: SCSI Status Error (probe1:ciss0:0:1:0): SCSI status: Check Condition (probe1:ciss0:0:1:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid command= operation code) (probe1:ciss0:0:1:0): Error 22, Unretryable error ugen4.1: <Intel> at usbus4 uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4 ugen5.1: <0x103c> at usbus5 uhub5: <0x103c UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 (probe2:ciss0:0:2:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0=20 (probe2:ciss0:0:2:0): CAM status: SCSI Status Error (probe2:ciss0:0:2:0): SCSI status: Check Condition (probe2:ciss0:0:2:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid command= operation code) (probe2:ciss0:0:2:0): Error 22, Unretryable error ipmi0: IPMI device rev. 1, firmware rev. 2.07, version 2.0 unknown: FAILURE - INQUIRY ILLEGAL REQUEST asc=3D0x24 ascq=3D0x00=20 ipmi0: Number of channels 0 (probe3:ciss0:0:3:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0=20 (probe3:ciss0:0:3:0): CAM status: SCSI Status Error (probe3:ciss0:0:3:0): SCSI status: Check Condition (probe3:ciss0:0:3:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid command= operation code) (probe3:ciss0:0:3:0): Error 22, Unretryable error ipmi0: Attached watchdog (probe4:ciss0:0:4:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0=20 (probe4:ciss0:0:4:0): CAM status: SCSI Status Error (probe4:ciss0:0:4:0): SCSI status: Check Condition (probe4:ciss0:0:4:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid command= operation code) (probe4:ciss0:0:4:0): Error 22, Unretryable error (probe5:ciss0:0:5:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0=20 (probe5:ciss0:0:5:0): CAM status: SCSI Status Error (probe5:ciss0:0:5:0): SCSI status: Check Condition (probe5:ciss0:0:5:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid command= operation code) (probe5:ciss0:0:5:0): Error 22, Unretryable error (probe6:ciss0:0:6:0): REPORT LUNS. CDB: a0 0 0 0 0 0 0 0 0 10 0 0=20 (probe6:ciss0:0:6:0): CAM status: SCSI Status Error (probe6:ciss0:0:6:0): SCSI status: Check Condition (probe6:ciss0:0:6:0): SCSI sense: ILLEGAL REQUEST asc:20,0 (Invalid command= operation code) (probe6:ciss0:0:6:0): Error 22, Unretryable error da0 at ciss0 bus 0 scbus0 target 0 lun 0 da0: <COMPAQ RAID 1(1VOLUME OK> Fixed Direct Access SCSI-5 device=20 da0: 135.168MB/s transfers da0: Command Queueing enabled da0: 238440MB (488327040 512 byte sectors: 255H 32S/T 59844C) da1 at ciss0 bus 0 scbus0 target 1 lun 0 da1: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-5 device=20 da1: 135.168MB/s transfers da1: Command Queueing enabled da1: 953837MB (1953459632 512 byte sectors: 255H 32S/T 65535C) da2 at ciss0 bus 0 scbus0 target 2 lun 0 da2: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-5 device=20 da2: 135.168MB/s transfers da2: Command Queueing enabled da2: 953837MB (1953459632 512 byte sectors: 255H 32S/T 65535C) da3 at ciss0 bus 0 scbus0 target 3 lun 0 da3: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-5 device=20 da3: 135.168MB/s transfers da3: Command Queueing enabled da3: 953837MB (1953459632 512 byte sectors: 255H 32S/T 65535C) da4 at ciss0 bus 0 scbus0 target 4 lun 0 da4: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-5 device=20 da4: 135.168MB/s transfers da4: Command Queueing enabled da4: 953837MB (1953459632 512 byte sectors: 255H 32S/T 65535C) da5 at ciss0 bus 0 scbus0 target 5 lun 0 da5: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-5 device=20 da5: 135.168MB/s transfers da5: Command Queueing enabled da5: 953837MB (1953459632 512 byte sectors: 255H 32S/T 65535C) da6 at ciss0 bus 0 scbus0 target 6 lun 0 da6: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-5 device=20 da6: 135.168MB/s transfers da6: Command Queueing enabled da6: 953837MB (1953459632 512 byte sectors: 255H 32S/T 65535C) sa0 at ciss1 bus 32 scbus3 target 3 lun 0 sa0: <HP Ultrium 3-SCSI Q24D> Removable Sequential Access SCSI-5 device=20 sa0: 135.168MB/s transfers sa0: Command Queueing enabled sa1 at mpt0 bus 0 scbus4 target 5 lun 0 sa1: <HP Ultrium 3-SCSI Q25W> Removable Sequential Access SCSI-5 device=20 sa1: 300.000MB/s transfers sa1: Command Queueing enabled cd0 at ata3 bus 0 scbus6 target 0 lun 0 cd0: <HL-DT-ST DVD-ROM DH10N DAE1> Removable CD-ROM SCSI-0 device=20 cd0: 3.300MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present - t= ray closed ch0 at mpt0 bus 0 scbus4 target 5 lun 1 ch0: <HP 1x8 G2 AUTOLDR 3.80> Removable Changer SCSI-5 device=20 ch0: 300.000MB/s transfers ch0: Command Queueing enabled SMP: AP CPU #3 Launched! ch0: 8 slots, 1 drive, 1 picker, 0 portals SMP: AP CPU #2 Launched! SMP: AP CPU #1 Launched! Timecounter "TSC-low" frequency 15625916 Hz quality 1000 GEOM: da3: the primary GPT table is corrupt or invalid. GEOM: da3: using the secondary instead -- recovery strongly advised. GEOM: da4: the primary GPT table is corrupt or invalid. GEOM: da4: using the secondary instead -- recovery strongly advised. GEOM: da5: the primary GPT table is corrupt or invalid. GEOM: da5: using the secondary instead -- recovery strongly advised. GEOM: da6: the primary GPT table is corrupt or invalid. GEOM: da6: using the secondary instead -- recovery strongly advised. Root mount waiting for: usbus5 usbus4 usbus3 usbus2 usbus1 usbus0 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub5: 2 ports with 2 removable, self powered uhub3: 2 ports with 2 removable, self powered Root mount waiting for: usbus5 usbus4 ugen5.2: <HP> at usbus5 ukbd0: <Virtual Keyboard> on usbus5 kbd2 at ukbd0 ums0: <Virtual Mouse> on usbus5 ums0: 3 buttons and [XY] coordinates ID=3D0 Root mount waiting for: usbus4 Root mount waiting for: usbus4 uhub4: 8 ports with 8 removable, self powered Trying to mount root from zfs:rpool []... ugen3.2: <EATON Powerware> at usbus3 =3D=3D dmesg =3D=3D --=20 Erfahrung hei=DFt gar nichts. Man kann seine Sache auch 35 Jahre schlecht machen. =20 -- Kurt Tucholsky
Responsible Changed From-To: freebsd-fs->avg Watch. This problem is potentially fixed.
State Changed From-To: open->closed I believe that this problem has been fixed in r243025. Please let me know if you still experience it.