D-Link DGE-530T (which is on the HCL) is visible in pciconf but not being recognized by sk(4). Possibly a new hardware revision? Here is the `pciconf -lv` output - none2@pci0:3:1:0: class=0x020000 card=0x43021186 chip=0x43021186 rev=0x10 hdr=0x00 vendor = 'D-Link System Inc' class = network subclass = ethernet
Confirmed that it is a new hardware version. sk(4) appears to support A1 and B1, the box for this card says "H/W Ver.:C1".
Responsible Changed From-To: freebsd-bugs->freebsd-net Over to maintainer(s).
State Changed From-To: open->feedback Please apply patch at the following URL and rebuild your kernel. http://people.freebsd.org/~yongari/sk/sk.dge530.diff Let me know it goes on your box.
Responsible Changed From-To: freebsd-net->yongari Grab.
Applied the patch, rebuilt and installed GENERIC, getting an error during boot - dmesg - skc0: <D-Link DGE-530T Gigabit Ethernet> port 0xe800-0xe8ff mem 0xfebffc00-0xfebffcff irq 17 at device 1.0 on pci3 skc0: couldn't allocate I/O resources device_attach: skc0 attach returned 6 ifconfig -l - rob@storm:~$ ifconfig -l re0 usbus0 usbus1 usbus2 usbus3 usbus4 lo0 rob@storm:~$ pciconf - skc0@pci0:3:1:0: class=0x020000 card=0x43021186 chip=0x43021186 rev=0x10 hdr=0x00 vendor = 'D-Link System Inc' class = network subclass = ethernet
On Fri, Jul 22, 2011 at 09:20:16PM +0000, Rob V wrote: > The following reply was made to PR kern/159116; it has been noted by GNATS. > > From: "Rob V" <rob@ipninja.net> > To: <bug-followup@FreeBSD.org>, <rob@ipninja.net> > Cc: > Subject: Re: kern/159116: [sk] New D-Link DGE-530T revision not supported by sk(4) > Date: Fri, 22 Jul 2011 17:14:22 -0400 > > Applied the patch, rebuilt and installed GENERIC, getting an error during > boot - > > > dmesg - > > skc0: <D-Link DGE-530T Gigabit Ethernet> port 0xe800-0xe8ff mem > 0xfebffc00-0xfebffcff irq 17 at device 1.0 on pci3 > skc0: couldn't allocate I/O resources > device_attach: skc0 attach returned 6 > Hmm, this looks strange. Could you show me full dmesg and "pciconf -lcbv" output? > > ifconfig -l - > > rob@storm:~$ ifconfig -l > re0 usbus0 usbus1 usbus2 usbus3 usbus4 lo0 > rob@storm:~$ > > > pciconf - > > skc0@pci0:3:1:0: class=0x020000 card=0x43021186 chip=0x43021186 > rev=0x10 hdr=0x00 > vendor = 'D-Link System Inc' > class = network > subclass = ethernet >
Full dmesg - Copyright (c) 1992-2011 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.2-STABLE #2: Fri Jul 22 18:03:21 EDT 2011 rob@storm.ipninja.net:/usr/obj/usr/src/sys/GENERIC i386 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (2999.94-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Family = f Model = 2 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA ,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x4400<CNXT-ID,xTPR> real memory = 2147483648 (2048 MB) avail memory = 2077077504 (1980 MB) ACPI APIC Table: <080510 APIC1418> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads cpu0 (BSP): APIC ID: 0 cpu1 (AP/HT): APIC ID: 1 ioapic0: Changing APIC ID to 2 ioapic0 <Version 2.0> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <080510 RSDT1418> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 7f600000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 vgapci0: <VGA-compatible display> port 0xcc00-0xcc07 mem 0xfe980000-0xfe9fffff,0xd0000000-0xdfffffff,0xfe800000-0xfe8fffff irq 16 at device 2.0 on pci0 agp0: <Intel G33 SVGA controller> on vgapci0 agp0: aperture size is 256M, detected 7164k stolen memory pci0: <multimedia, HDA> at device 27.0 (no driver attached) pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0 pci2: <ACPI PCI bus> on pcib2 re0: <RealTek 810xE PCIe 10/100baseTX> port 0xd800-0xd8ff mem 0xfdfff000-0xfdffffff,0xfdfe0000-0xfdfeffff irq 17 at device 0.0 on pci2 re0: Using 1 MSI-X message re0: Chip rev. 0x24800000 re0: MAC rev. 0x00000000 miibus0: <MII bus> on re0 rlphy0: <RTL8201L 10/100 media interface> PHY 1 on miibus0 rlphy0: 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, auto, auto-flow re0: Ethernet address: 00:30:67:b9:a3:d1 re0: [ITHREAD] uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0xc880-0xc89f irq 23 at device 29.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x2f00 usbus0: <Intel 82801G (ICH7) USB controller USB-A> on uhci0 uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0xc800-0xc81f irq 19 at device 29.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x2f00 usbus1: <Intel 82801G (ICH7) USB controller USB-B> on uhci1 uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0xc480-0xc49f irq 18 at device 29.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x2f00 usbus2: <Intel 82801G (ICH7) USB controller USB-C> on uhci2 uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0xc400-0xc41f irq 16 at device 29.3 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x2f00 usbus3: <Intel 82801G (ICH7) USB controller USB-D> on uhci3 ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xfe977c00-0xfe977fff irq 23 at device 29.7 on pci0 ehci0: [ITHREAD] usbus4: EHCI version 1.0 usbus4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0 pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci3: <ACPI PCI bus> on pcib3 skc0: <D-Link DGE-530T Gigabit Ethernet> port 0xe800-0xe8ff mem 0xfebffc00-0xfebffcff irq 17 at device 1.0 on pci3 skc0: couldn't allocate I/O resources device_attach: skc0 attach returned 6 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] atapci1: <Intel ICH7 SATA300 controller> port 0xc080-0xc087,0xc000-0xc003,0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb80f irq 19 at device 31.2 on pci0 atapci1: [ITHREAD] ata2: <ATA channel 0> on atapci1 ata2: [ITHREAD] ata3: <ATA channel 1> on atapci1 ata3: [ITHREAD] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) acpi_button0: <Power Button> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: [FILTER] pmtimer0 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] ppc0: parallel port not found. p4tcc0: <CPU Frequency Thermal Control> on cpu0 p4tcc1: <CPU Frequency Thermal Control> on cpu1 ZFS filesystem version 5 ZFS storage pool version 28 Timecounters tick every 1.000 msec usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 12Mbps Full Speed USB v1.0 usbus4: 480Mbps High Speed USB v2.0 acd0: DVDROM <IDE DVD-ROM 16X/VER 2.21> at ata0-master UDMA33 ugen0.1: <Intel> at usbus0 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <Intel> at usbus1 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen2.1: <Intel> at usbus2 uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <Intel> at usbus3 uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 ugen4.1: <Intel> at usbus4 uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4 ad4: 76319MB <WDC WD800JB-00ETA0 77.07W77> at ata2-master UDMA100 SATA ad6: 152627MB <WDC WD1600JD-00HBB0 08.02D08> at ata3-master UDMA100 SATA SMP: AP CPU #1 Launched! Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub3: 2 ports with 2 removable, self powered Root mount waiting for: usbus4 Root mount waiting for: usbus4 Root mount waiting for: usbus4 uhub4: 8 ports with 8 removable, self powered Trying to mount root from zfs:zroot ugen1.2: <Microsoft> at usbus1 ukbd0: <Microsoft Comfort Curve Keyboard 2000, class 0/0, rev 2.00/1.73, addr 2> on usbus1 kbd2 at ukbd0 uhid0: <Microsoft Comfort Curve Keyboard 2000, class 0/0, rev 2.00/1.73, addr 2> on usbus1 storm# Full pciconf -lcbv - storm# pciconf -lcbv hostb0@pci0:0:0:0: class=0x060000 card=0x29c08086 chip=0x29c08086 rev=0x10 hdr=0x00 vendor = 'Intel Corporation' device = 'P35/G33 (Bearlake) Processor to I/O Controller' class = bridge subclass = HOST-PCI cap 09[e0] = vendor (length 11) Intel cap 11 version 1 vgapci0@pci0:0:2:0: class=0x030000 card=0x31031565 chip=0x29c28086 rev=0x10 hdr=0x00 vendor = 'Intel Corporation' device = 'P35/G33 (Bearlake) Integrated Graphics Controller' class = display subclass = VGA bar [10] = type Memory, range 32, base rxfe980000, size 524288, enabled bar [14] = type I/O Port, range 32, base rxcc00, size 8, enabled bar [18] = type Prefetchable Memory, range 32, base rxd0000000, size 268435456, enabled bar [1c] = type Memory, range 32, base rxfe800000, size 1048576, enabled cap 05[90] = MSI supports 1 message cap 01[d0] = powerspec 2 supports D0 D3 current D0 none0@pci0:0:27:0: class=0x040300 card=0x821e1565 chip=0x27d88086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = 'IDT High Definition Audio Driver (BA101897)' class = multimedia subclass = HDA bar [10] = type Memory, range 64, base rxfe978000, size 16384, enabled cap 01[50] = powerspec 2 supports D0 D3 current D0 cap 05[60] = MSI supports 1 message, 64 bit cap 10[70] = PCI-Express 1 root endpoint max data 128(128) link x0(x0) ecap 0002[100] = VC 1 max VC1 ecap 0005[130] = unknown 1 pcib1@pci0:0:28:0: class=0x060400 card=0x31031565 chip=0x27d08086 rev=0x01 hdr=0x01 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) PCIe Root Port' class = bridge subclass = PCI-PCI cap 10[40] = PCI-Express 1 root port max data 128(128) link x0(x1) cap 05[80] = MSI supports 1 message cap 0d[90] = PCI Bridge card=0x31031565 cap 01[a0] = powerspec 2 supports D0 D3 current D0 ecap 0002[100] = VC 1 max VC1 ecap 0005[180] = unknown 1 pcib2@pci0:0:28:1: class=0x060400 card=0x31031565 chip=0x27d28086 rev=0x01 hdr=0x01 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) PCIe Root Port' class = bridge subclass = PCI-PCI cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1) cap 05[80] = MSI supports 1 message cap 0d[90] = PCI Bridge card=0x31031565 cap 01[a0] = powerspec 2 supports D0 D3 current D0 ecap 0002[100] = VC 1 max VC1 ecap 0005[180] = unknown 1 uhci0@pci0:0:29:0: class=0x0c0300 card=0x31031565 chip=0x27c88086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) USB Universal Host Controller' class = serial bus subclass = USB bar [20] = type I/O Port, range 32, base rxc880, size 32, enabled uhci1@pci0:0:29:1: class=0x0c0300 card=0x31031565 chip=0x27c98086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) USB Universal Host Controller' class = serial bus subclass = USB bar [20] = type I/O Port, range 32, base rxc800, size 32, enabled uhci2@pci0:0:29:2: class=0x0c0300 card=0x31031565 chip=0x27ca8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) USB Universal Host Controller' class = serial bus subclass = USB bar [20] = type I/O Port, range 32, base rxc480, size 32, enabled uhci3@pci0:0:29:3: class=0x0c0300 card=0x31031565 chip=0x27cb8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) USB Universal Host Controller' class = serial bus subclass = USB bar [20] = type I/O Port, range 32, base rxc400, size 32, enabled ehci0@pci0:0:29:7: class=0x0c0320 card=0x31031565 chip=0x27cc8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) USB 2.0 Enhanced Host Controller' class = serial bus subclass = USB bar [10] = type Memory, range 32, base rxfe977c00, size 1024, enabled cap 01[50] = powerspec 2 supports D0 D3 current D0 cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14 pcib3@pci0:0:30:0: class=0x060401 card=0x31031565 chip=0x244e8086 rev=0xe1 hdr=0x01 vendor = 'Intel Corporation' device = '82801 Family (ICH2/3/4/5/6/7/8/9,63xxESB) Hub Interface to PCI Bridge' class = bridge subclass = PCI-PCI cap 0d[50] = PCI Bridge card=0x31031565 isab0@pci0:0:31:0: class=0x060100 card=0x31031565 chip=0x27b88086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = 'Intel 82801GB/GR (ICH7 Family) LPC Interface Controller - 27B8 (945GL)' class = bridge subclass = PCI-ISA cap 09[e0] = vendor (length 12) Intel cap 1 version 0 features: Quick Resume, SATA RAID-5, 6 PCI-e x1 slots, SATA RAID-0/1/10, SATA AHCI atapci0@pci0:0:31:1: class=0x01018a card=0x31031565 chip=0x27df8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801G (ICH7 Family) Ultra ATA Storage Controller' class = mass storage subclass = ATA bar [10] = type I/O Port, range 32, base rx1f0, size 8, enabled bar [14] = type I/O Port, range 32, base rx3f4, size 1, enabled bar [18] = type I/O Port, range 32, base rx170, size 8, enabled bar [1c] = type I/O Port, range 32, base rx374, size 1, enabled bar [20] = type I/O Port, range 32, base rxffa0, size 16, enabled atapci1@pci0:0:31:2: class=0x01018f card=0x52021565 chip=0x27c08086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = '82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller' class = mass storage subclass = ATA bar [10] = type I/O Port, range 32, base rxc080, size 8, enabled bar [14] = type I/O Port, range 32, base rxc000, size 4, enabled bar [18] = type I/O Port, range 32, base rxbc00, size 8, enabled bar [1c] = type I/O Port, range 32, base rxb880, size 4, enabled bar [20] = type I/O Port, range 32, base rxb800, size 16, enabled cap 01[70] = powerspec 2 supports D0 D3 current D0 none1@pci0:0:31:3: class=0x0c0500 card=0x31031565 chip=0x27da8086 rev=0x01 hdr=0x00 vendor = 'Intel Corporation' device = 'Intel[R] 82801G (ICH7 Family) C- 27DA (82801G)' class = serial bus subclass = SMBus bar [20] = type I/O Port, range 32, base rx400, size 32, enabled re0@pci0:2:0:0: class=0x020000 card=0x23081565 chip=0x813610ec rev=0x02 hdr=0x00 vendor = 'Realtek Semiconductor' device = 'Realtek 10/100/1000 PCI-E NIC Family all in one NDIS Driver v5.728.0604.2009 06/04/2009 (Rtl8023)' class = network subclass = ethernet bar [10] = type I/O Port, range 32, base rxd800, size 256, enabled bar [18] = type Prefetchable Memory, range 64, base rxfdfff000, size 4096, enabled bar [20] = type Prefetchable Memory, range 64, base rxfdfe0000, size 65536, enabled cap 01[40] = powerspec 3 supports D0 D1 D2 D3 current D0 cap 05[50] = MSI supports 1 message, 64 bit cap 10[70] = PCI-Express 2 endpoint IRQ 2 max data 128(256) link x1(x1) cap 11[ac] = MSI-X supports 2 messages in map 0x20 enabled cap 03[cc] = VPD ecap 0001[100] = AER 1 0 fatal 0 non-fatal 2 corrected ecap 0002[140] = VC 1 max VC0 ecap 0003[160] = Serial 1 4d010000ffff0000 skc0@pci0:3:1:0: class=0x020000 card=0x43021186 chip=0x43021186 rev=0x10 hdr=0x00 vendor = 'D-Link System Inc' class = network subclass = ethernet bar [10] = type I/O Port, range 32, base rxe800, size 256, enabled bar [14] = type Memory, range 32, base rxfebffc00, size 256, enabled cap 01[dc] = powerspec 2 supports D0 D1 D2 D3 current D0 storm#
On Fri, Jul 22, 2011 at 06:39:25PM -0400, Rob V wrote: > Full dmesg - > [...] > Full pciconf -lcbv - > > storm# pciconf -lcbv > hostb0@pci0:0:0:0: class=0x060000 card=0x29c08086 chip=0x29c08086 > rev=0x10 hdr=0x00 > vendor = 'Intel Corporation' > device = 'P35/G33 (Bearlake) Processor to I/O Controller' > class = bridge > subclass = HOST-PCI > cap 09[e0] = vendor (length 11) Intel cap 11 version 1 [...] > skc0@pci0:3:1:0: class=0x020000 card=0x43021186 chip=0x43021186 > rev=0x10 hdr=0x00 > vendor = 'D-Link System Inc' > class = network > subclass = ethernet > bar [10] = type I/O Port, range 32, base rxe800, size 256, enabled > bar [14] = type Memory, range 32, base rxfebffc00, size 256, enabled > cap 01[dc] = powerspec 2 supports D0 D1 D2 D3 current D0 Now I can see why the vendor changed revision number. Now BAR1 is memory mapping. Would you back out changes made in previous patch and try the following diff again? http://people.freebsd.org/~yongari/sk/sk.dge530.diff2 Thanks.
That caused a - page fault, panic, reboot - loop which took me about 3 hours to recover from ... and from that I learned I should always have a known good and stable kernel somewhere handy during this process :-) I'm afraid the best I could do is a picture of the screen with my digital camera as I don't have a serial port on that box yet to use for the console ... http://s1108.photobucket.com/albums/h417/robatipninjadotnet/?action=view&cur rent=M2680001.jpg -----Original Message----- From: YongHyeon PYUN [mailto:pyunyh@gmail.com] Sent: July-22-11 7:26 PM To: Rob V Cc: yongari@freebsd.org; bug-followup@freebsd.org Subject: Re: kern/159116: [sk] New D-Link DGE-530T revision not supported by sk(4) On Fri, Jul 22, 2011 at 06:39:25PM -0400, Rob V wrote: > Full dmesg - > [...] > Full pciconf -lcbv - > > storm# pciconf -lcbv > hostb0@pci0:0:0:0: class=0x060000 card=0x29c08086 chip=0x29c08086 > rev=0x10 hdr=0x00 > vendor = 'Intel Corporation' > device = 'P35/G33 (Bearlake) Processor to I/O Controller' > class = bridge > subclass = HOST-PCI > cap 09[e0] = vendor (length 11) Intel cap 11 version 1 [...] > skc0@pci0:3:1:0: class=0x020000 card=0x43021186 chip=0x43021186 > rev=0x10 hdr=0x00 > vendor = 'D-Link System Inc' > class = network > subclass = ethernet > bar [10] = type I/O Port, range 32, base rxe800, size 256, enabled > bar [14] = type Memory, range 32, base rxfebffc00, size 256, enabled > cap 01[dc] = powerspec 2 supports D0 D1 D2 D3 current D0 Now I can see why the vendor changed revision number. Now BAR1 is memory mapping. Would you back out changes made in previous patch and try the following diff again? http://people.freebsd.org/~yongari/sk/sk.dge530.diff2 Thanks.
Found the additional crash info I was unable to get from the screen in dmesg - Copyright (c) 1992-2011 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.2-STABLE #2: Wed Jul 27 11:29:33 EDT 2011 rob@storm.ipninja.net:/usr/src/sys/i386/compile/GENERIC i386 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (2999.95-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Family = f Model = 2 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA ,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x4400<CNXT-ID,xTPR> real memory = 2147483648 (2048 MB) avail memory = 2084290560 (1987 MB) ACPI APIC Table: <080510 APIC1418> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads cpu0 (BSP): APIC ID: 0 cpu1 (AP/HT): APIC ID: 1 ioapic0: Changing APIC ID to 2 ioapic0 <Version 2.0> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <080510 RSDT1418> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 7fd00000 (3) failed Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 vgapci0: <VGA-compatible display> port 0xcc00-0xcc07 mem 0xfe980000-0xfe9fffff,0xd0000000-0xdfffffff,0xfe800000-0xfe8fffff irq 16 at device 2.0 on pci0 agp0: <Intel G33 SVGA controller> on vgapci0 agp0: aperture size is 256M, detected 4194300k stolen memory pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0 pci2: <ACPI PCI bus> on pcib2 re0: <RealTek 810xE PCIe 10/100baseTX> port 0xd800-0xd8ff mem 0xfdfff000-0xfdffffff,0xfdfe0000-0xfdfeffff irq 17 at device 0.0 on pci2 re0: Using 1 MSI-X message re0: Chip rev. 0x24800000 re0: MAC rev. 0x00000000 miibus0: <MII bus> on re0 rlphy0: <RTL8201L 10/100 media interface> PHY 1 on miibus0 rlphy0: 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, auto, auto-flow re0: Ethernet address: 00:30:67:b9:a3:d1 re0: [ITHREAD] uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0xc880-0xc89f irq 23 at device 29.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x2f00 usbus0: <Intel 82801G (ICH7) USB controller USB-A> on uhci0 uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0xc800-0xc81f irq 19 at device 29.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x2f00 usbus1: <Intel 82801G (ICH7) USB controller USB-B> on uhci1 uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0xc480-0xc49f irq 18 at device 29.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x2f00 usbus2: <Intel 82801G (ICH7) USB controller USB-C> on uhci2 uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0xc400-0xc41f irq 16 at device 29.3 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x2f00 usbus3: <Intel 82801G (ICH7) USB controller USB-D> on uhci3 ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xfe97bc00-0xfe97bfff irq 23 at device 29.7 on pci0 ehci0: [ITHREAD] usbus4: EHCI version 1.0 usbus4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0 pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci3: <ACPI PCI bus> on pcib3 skc0: <D-Link DGE-530T Gigabit Ethernet> port 0xe800-0xe8ff mem 0xfebffc00-0xfebffcff irq 17 at device 1.0 on pci3 Fatal trap 12: page fault while in kernel mode cpuid = 0; apic id = 00 fault virtual address = 0xfc49fb10 fault code = supervisor write, page not present instruction pointer = 0x20:0xc074df92 stack pointer = 0x28:0xc1420854 frame pointer = 0x28:0xc1420864 code segment = base rx0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 0 (swapper) trap number = 12 panic: page fault cpuid = 0 KDB: stack backtrace: #0 0xc08c93e9 at kdb_backtrace+0x43 #1 0xc089ac8e at panic+0x114 #2 0xc0bb73bc at trap_fatal+0x320 #3 0xc0bb762c at trap_pfault+0x264 #4 0xc0bb7b3b at trap+0x44a #5 0xc0b9f7bc at calltrap+0x6 #6 0xc0753fa1 at skc_attach+0x40e #7 0xc08c3ac4 at device_attach+0x36a #8 0xc08c4cca at device_probe_and_attach+0x2d #9 0xc08c4ce9 at bus_generic_attach+0x19 #10 0xc04e4387 at acpi_pci_attach+0x193 #11 0xc08c3ac4 at device_attach+0x36a #12 0xc08c4cca at device_probe_and_attach+0x2d #13 0xc08c4ce9 at bus_generic_attach+0x19 #14 0xc04e6141 at acpi_pcib_attach+0x18f #15 0xc04e7003 at acpi_pcib_pci_attach+0x97 #16 0xc08c3ac4 at device_attach+0x36a -----Original Message----- From: YongHyeon PYUN [mailto:pyunyh@gmail.com] Sent: July-22-11 7:26 PM To: Rob V Cc: yongari@freebsd.org; bug-followup@freebsd.org Subject: Re: kern/159116: [sk] New D-Link DGE-530T revision not supported by sk(4) On Fri, Jul 22, 2011 at 06:39:25PM -0400, Rob V wrote: > Full dmesg - > [...] > Full pciconf -lcbv - > > storm# pciconf -lcbv > hostb0@pci0:0:0:0: class=0x060000 card=0x29c08086 chip=0x29c08086 > rev=0x10 hdr=0x00 > vendor = 'Intel Corporation' > device = 'P35/G33 (Bearlake) Processor to I/O Controller' > class = bridge > subclass = HOST-PCI > cap 09[e0] = vendor (length 11) Intel cap 11 version 1 [...] > skc0@pci0:3:1:0: class=0x020000 card=0x43021186 chip=0x43021186 > rev=0x10 hdr=0x00 > vendor = 'D-Link System Inc' > class = network > subclass = ethernet > bar [10] = type I/O Port, range 32, base rxe800, size 256, enabled > bar [14] = type Memory, range 32, base rxfebffc00, size 256, enabled > cap 01[dc] = powerspec 2 supports D0 D1 D2 D3 current D0 Now I can see why the vendor changed revision number. Now BAR1 is memory mapping. Would you back out changes made in previous patch and try the following diff again? http://people.freebsd.org/~yongari/sk/sk.dge530.diff2 Thanks.
On suspicion that this wasn't an sk supported controller yongari asked me to take a picture of the card and then sent me a patch for re that appears to work perfectly - re1: <D-Link DGE-530(T) Gigabit Ethernet Adapter> port 0xe800-0xe8ff mem 0xfebffc00-0xfebffcff irq 17 at device 1.0 on pci3 re1: Chip rev. 0x10000000 re1: MAC rev. 0x00000000 miibus1: <MII bus> on re1 rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1 rgephy0: 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re1: Ethernet address: 5c:d9:98:ae:37:39 re1: [FILTER] re1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=389b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_UCAST,WOL _MCAST,WOL_MAGIC> ether 5c:d9:98:ae:37:39 inet 172.30.0.50 netmask 0xffffff00 broadcast 172.30.0.255 inet6 fe80::5ed9:98ff:feae:3739%re1 prefixlen 64 scopeid 0x7 inet6 2001:<snip>:cafa prefixlen 64 nd6 options=3<PERFORMNUD,ACCEPT_RTADV> media: Ethernet autoselect (1000baseT <full-duplex>) status: active
Author: yongari Date: Sat Jul 30 01:06:12 2011 New Revision: 224506 URL: http://svn.freebsd.org/changeset/base/224506 Log: Add new device id of D-Link DGE-530T Rev. C controller. DGE-503T Rev A1 and B1 is supported by sk(4) but the DGE-530T Rev. C controller is re-branded RealTek 8169 controller. PR: kern/159116 Approved by: re (kib) Modified: head/sys/dev/re/if_re.c head/sys/pci/if_rlreg.h Modified: head/sys/dev/re/if_re.c ============================================================================== --- head/sys/dev/re/if_re.c Sat Jul 30 00:52:13 2011 (r224505) +++ head/sys/dev/re/if_re.c Sat Jul 30 01:06:12 2011 (r224506) @@ -174,6 +174,8 @@ TUNABLE_INT("hw.re.prefer_iomap", &prefe static struct rl_type re_devs[] = { { DLINK_VENDORID, DLINK_DEVICEID_528T, 0, "D-Link DGE-528(T) Gigabit Ethernet Adapter" }, + { DLINK_VENDORID, DLINK_DEVICEID_530T_REVC, 0, + "D-Link DGE-530(T) Gigabit Ethernet Adapter" }, { RT_VENDORID, RT_DEVICEID_8139, 0, "RealTek 8139C+ 10/100BaseTX" }, { RT_VENDORID, RT_DEVICEID_8101E, 0, Modified: head/sys/pci/if_rlreg.h ============================================================================== --- head/sys/pci/if_rlreg.h Sat Jul 30 00:52:13 2011 (r224505) +++ head/sys/pci/if_rlreg.h Sat Jul 30 01:06:12 2011 (r224506) @@ -1042,6 +1042,7 @@ struct rl_softc { * D-Link DFE-5280T device ID */ #define DLINK_DEVICEID_528T 0x4300 +#define DLINK_DEVICEID_530T_REVC 0x4302 /* * D-Link DFE-690TXD device ID _______________________________________________ svn-src-all@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/svn-src-all To unsubscribe, send any mail to "svn-src-all-unsubscribe@freebsd.org"
State Changed From-To: feedback->patched Fixed in HEAD(r224506). Thanks for testing and reporting!
Author: yongari Date: Mon Aug 15 17:08:54 2011 New Revision: 224891 URL: http://svn.freebsd.org/changeset/base/224891 Log: MFC r224506: Add new device id of D-Link DGE-530T Rev. C controller. DGE-503T Rev A1 and B1 is supported by sk(4) but the DGE-530T Rev. C controller is re-branded RealTek 8169 controller. PR: kern/159116 Modified: stable/8/sys/dev/re/if_re.c stable/8/sys/pci/if_rlreg.h Directory Properties: stable/8/sys/ (props changed) stable/8/sys/amd64/include/xen/ (props changed) stable/8/sys/cddl/contrib/opensolaris/ (props changed) stable/8/sys/contrib/dev/acpica/ (props changed) stable/8/sys/contrib/pf/ (props changed) Modified: stable/8/sys/dev/re/if_re.c ============================================================================== --- stable/8/sys/dev/re/if_re.c Mon Aug 15 16:06:28 2011 (r224890) +++ stable/8/sys/dev/re/if_re.c Mon Aug 15 17:08:54 2011 (r224891) @@ -174,6 +174,8 @@ TUNABLE_INT("hw.re.prefer_iomap", &prefe static struct rl_type re_devs[] = { { DLINK_VENDORID, DLINK_DEVICEID_528T, 0, "D-Link DGE-528(T) Gigabit Ethernet Adapter" }, + { DLINK_VENDORID, DLINK_DEVICEID_530T_REVC, 0, + "D-Link DGE-530(T) Gigabit Ethernet Adapter" }, { RT_VENDORID, RT_DEVICEID_8139, 0, "RealTek 8139C+ 10/100BaseTX" }, { RT_VENDORID, RT_DEVICEID_8101E, 0, Modified: stable/8/sys/pci/if_rlreg.h ============================================================================== --- stable/8/sys/pci/if_rlreg.h Mon Aug 15 16:06:28 2011 (r224890) +++ stable/8/sys/pci/if_rlreg.h Mon Aug 15 17:08:54 2011 (r224891) @@ -1042,6 +1042,7 @@ struct rl_softc { * D-Link DFE-5280T device ID */ #define DLINK_DEVICEID_528T 0x4300 +#define DLINK_DEVICEID_530T_REVC 0x4302 /* * D-Link DFE-690TXD device ID _______________________________________________ svn-src-all@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/svn-src-all To unsubscribe, send any mail to "svn-src-all-unsubscribe@freebsd.org"
Author: yongari Date: Mon Aug 15 17:10:23 2011 New Revision: 224892 URL: http://svn.freebsd.org/changeset/base/224892 Log: MFC r224506: Add new device id of D-Link DGE-530T Rev. C controller. DGE-503T Rev A1 and B1 is supported by sk(4) but the DGE-530T Rev. C controller is re-branded RealTek 8169 controller. PR: kern/159116 Modified: stable/7/sys/dev/re/if_re.c stable/7/sys/pci/if_rlreg.h Directory Properties: stable/7/sys/ (props changed) stable/7/sys/cddl/contrib/opensolaris/ (props changed) stable/7/sys/contrib/dev/acpica/ (props changed) stable/7/sys/contrib/pf/ (props changed) Modified: stable/7/sys/dev/re/if_re.c ============================================================================== --- stable/7/sys/dev/re/if_re.c Mon Aug 15 17:08:54 2011 (r224891) +++ stable/7/sys/dev/re/if_re.c Mon Aug 15 17:10:23 2011 (r224892) @@ -174,6 +174,8 @@ TUNABLE_INT("hw.re.prefer_iomap", &prefe static struct rl_type re_devs[] = { { DLINK_VENDORID, DLINK_DEVICEID_528T, 0, "D-Link DGE-528(T) Gigabit Ethernet Adapter" }, + { DLINK_VENDORID, DLINK_DEVICEID_530T_REVC, 0, + "D-Link DGE-530(T) Gigabit Ethernet Adapter" }, { RT_VENDORID, RT_DEVICEID_8139, 0, "RealTek 8139C+ 10/100BaseTX" }, { RT_VENDORID, RT_DEVICEID_8101E, 0, Modified: stable/7/sys/pci/if_rlreg.h ============================================================================== --- stable/7/sys/pci/if_rlreg.h Mon Aug 15 17:08:54 2011 (r224891) +++ stable/7/sys/pci/if_rlreg.h Mon Aug 15 17:10:23 2011 (r224892) @@ -1042,6 +1042,7 @@ struct rl_softc { * D-Link DFE-5280T device ID */ #define DLINK_DEVICEID_528T 0x4300 +#define DLINK_DEVICEID_530T_REVC 0x4302 /* * D-Link DFE-690TXD device ID _______________________________________________ svn-src-all@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/svn-src-all To unsubscribe, send any mail to "svn-src-all-unsubscribe@freebsd.org"
State Changed From-To: patched->closed MFC to stable/8 and stable/7 done. Thanks for testing!