Dell E6520 can't resume after suspend - power is on but nothing can be seen on LCD. I did a procedure described in Handbook: - sysctl debug.bootverbose=1 - sysctl debug.acpi.suspend_bounce=1 - acpiconf -s 3 Output from console: ehci0: wake_prep disabled wake for \_SB_.PCI0.EHC2 (S3) ehci1: wake_prep disabled wake for \_SB_.PCI0.EHCI (S3) acpi_lid0: wake_prep enabled for \_SB_.LID_ (S3) acpi_button0: wake_prep enabled for \_SB_.PBTN (S3) pci0:0:25:0: Transition from D3 to D0 pci0:0:27:0: Transition from D3 to D0 pci0:0:31:2: Transition from D3 to D0 pci0:1:0:0: Transition from D3 to D0 pci0:1:0:1: Transition from D3 to D0 vgapci0: calling BIOS POST hdac1: Enabling headphone/speaker audio routing switching: hdac1: as=0 sense nid=11 [UNSOL] hdac1: Pin sense: nid=11 res=0x00000000 pci0:3:0:0: Transition from D3 to D0 pci0:11:0:0: Transition from D3 to D0 pci0:11:0:1: Transition from D3 to D0 fwohci0: Phy 1394a available S400, 1 ports. fwohci0: Link S400, max_rec 2048 bytes. fwohci0: Initiate bus reset fwohci0: fwohci_intr_core: BUS reset fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, non CYCLEMASTER mode firewire0: 2 nodes, maxhop <= 1 cable IRM irm(1) mmc0: Probing bus mmc0: SD 2.0 interface conditions: OK mmc0: SD probe: OK (OCR: 0x00ff8000) mmc0: Current OCR: 0x00ff8000 firewire0: fw_rcv: unknown response RRESQ(6) src=0xffc1 tl=0x1 rt=1 data=0xdd284f04 mmc0: Probing cards mmc0: Card detected (CID 275048534430384730b00005b400a500) mmc0: Card at relative address 7: mmc0: card: SD High Capacity (0x27/0x5048/"SD08G" rev 3.0 m/d 05.2010 s/n b00005b4) mmc0: bus: 4bit, 50MHz, high speed timing mmc0: memory: 15704064 blocks, erase sector 8192 blocks mmc0: setting transfer rate to 50.000MHz (high speed timing) ahcich0: AHCI reset... ahcich0: SATA connect time=1000us status=00000123 ahcich0: AHCI reset: device found ahcich1: AHCI reset... ahcich1: SATA connect time=1800us status=00000113 ahcich1: AHCI reset: device found ahcich1: AHCI reset: device ready after 0ms ahcich2: AHCI reset... ahcich2: SATA connect timeout time=10000us status=00000000 ahcich2: AHCI reset: device not found ahcich3: AHCI reset... ahcich3: SATA connect timeout time=10000us status=00000000 ahcich3: AHCI reset: device not found ahcich4: AHCI reset... ahcich4: SATA connect timeout time=10000us status=00000000 ahcich4: AHCI reset: device not found battery1: battery0: battery2: battery initialization start battery initialization start battery initialization start battery0: battery initialization done, tried 1 times atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa firewire0: ahcich0: split transaction timeout: tl=0x15 flag=0x04 AHCI reset: device ready after 100ms send: dst=0x01 tl=0x15 rt=0 tcode=0x4 pri=0x0 src=0x000 firewire0: fw_explore_node: node1: explore_read_quads failure firewire0: fw_rcv: unknown response RRESQ(6) src=0xffc1 tl=0x2 rt=1 data=0x34393331 uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0 firewire0: split transaction timeout: tl=0x16 flag=0x04 send: dst=0x01 tl=0x16 rt=0 tcode=0x4 pri=0x0 src=0x000 firewire0: fw_explore_node: node1: explore_read_quads failure firewire0: fw_rcv: unknown response RRESQ(6) src=0xffc1 tl=0x3 rt=1 data=0x12a064f0 firewire0: split transaction timeout: tl=0x17 flag=0x04 send: dst=0x01 tl=0x17 rt=0 tcode=0x4 pri=0x0 src=0x000 firewire0: fw_explore_node: node1: explore_read_quads failure uhub2: 6 ports with 6 removable, self powered ugen0.3: <Dell Computer Corp> at usbus0 ubt0: <Dell Computer Corp DW375 Bluetooth Module, class 224/1, rev 2.00/5.17, addr 3> on usbus0 ugen0.4: <CN0CJ3P27248717L025LA01> at usbus0 battery2: battery initialization failed, giving up battery1: battery initialization failed, giving up
Responsible Changed From-To: freebsd-bugs->freebsd-acpi reclassify.
For bugs matching the following criteria: Status: In Progress Changed: (is less than) 2014-06-01 Reset to default assignee and clear in-progress tags. Mail being skipped
I know it's been a while since you filed this bug, and I apologize for the tardy response. However, no version information was given and ACPI has changed significantly since then. So has the problem been resolved? Do you even still have this laptop?