Bug 173616 - LG USB DVD-RW USB STALL
Summary: LG USB DVD-RW USB STALL
Status: Closed Feedback Timeout
Alias: None
Product: Base System
Classification: Unclassified
Component: usb (show other bugs)
Version: 9.1-PRERELEASE
Hardware: Any Any
: Normal Affects Only Me
Assignee: freebsd-usb (Nobody)
URL:
Keywords:
Depends on:
Blocks:
 
Reported: 2012-11-13 22:00 UTC by hsu
Modified: 2015-12-25 05:00 UTC (History)
1 user (show)

See Also:

Attachments
Add an attachment (proposed patch, testcase, etc.)

Note You need to log in before you can comment on or make changes to this bug.
Description hsu 2012-11-13 22:00:00 UTC 
LG external USB DVD-RW fails.

ugen2.3: <product 0x2502 vendor 0x0424> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE
ugen2.9: <Super Multi Rewriter HLDS Inc.> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON

Kernel says the following:

ugen2.3: <vendor 0x0424> at usbus2
uhub9: <vendor 0x0424 product 0x2502, class 9/0, rev 2.00/0.01, addr 3> on usbus2
uhub9: 2 ports with 2 removable, self powered
ugen2.9: <HLDS Inc.> at usbus2
umass1: <HLDS Inc. Super Multi Rewriter, class 0/0, rev 2.00/0.00, addr 9> on usbus2
umass1:  SCSI over Bulk-Only; quirks = 0x0100
umass1:10:1:-1: Attached to scbus10
cd2 at umass-sim1 bus 1 scbus10 target 0 lun 0
cd2: <HL-DT-ST DVD-RAM GSA-E20N 1.03> Removable CD-ROM SCSI-0 device 
cd2: 40.000MB/s transfers
cd2: Attempt to query device size failed: NOT READY, Medium not present
usb_alloc_device: set address 10 failed (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 10 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=10, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 10 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=10, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 10 failed, USB_ERR_STALLED
ugen2.10: <Unknown> at usbus2 (disconnected)
uhub_reattach_port: could not allocate new device
usb_alloc_device: set address 10 failed (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 10 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=10, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 10 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=10, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 10 failed, USB_ERR_STALLED
ugen2.10: <Unknown> at usbus2 (disconnected)
uhub_reattach_port: could not allocate new device
usb_alloc_device: set address 10 failed (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 10 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=10, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 10 failed, USB_ERR_STALLED
usbd_req_re_enumerate: addr=10, set address failed! (USB_ERR_STALLED, ignored)
usbd_setup_device_desc: getting device descriptor at addr 10 failed, USB_ERR_STALLED
ugen2.10: <Unknown> at usbus2 (disconnected)
uhub_reattach_port: could not allocate new device
uhub_reattach_port: port 2 reset failed, error=USB_ERR_STALLED
uhub_reattach_port: device problem (USB_ERR_STALLED), disabling port 2
ugen2.3: <vendor 0x0424> at usbus2 (disconnected)
uhub9: at uhub8, port 4, addr 3 (disconnected)
ugen2.9: <HLDS Inc.> at usbus2 (disconnected)
umass1: at uhub9, port 1, addr 9 (disconnected)
(cd2:umass-sim1:1:0:0): lost device, 1 refs
(cd2:(pass7:umass-sim1:1:umass-sim1:1:0:0:0): removing device entry
0): passdevgonecb: devfs entry is gone

When trying to access the drive, device not configured error results.


All usbconfig commands become very slow when the drive is plugged in.
It seems that some other devices may fail at the same moment (grip
ripping a cd on another dvd drive might hang, for example).


I have tried some USB quirks

UQ_MSC_NO_GETMAXLUN (just a guess)

UQ_OPEN_CLEARSTALL (some discussion referred to this)

UQ_MSC_FORCE_PROTO_ATAPI (device seems to default to scsi)

None of these had any effect, other than last one changing protocol to ATAPI.

This device may have worked with past FreeBSD versions.

Drive is externally powered, not USB powered.

Fix: 

No idea.
How-To-Repeat: 
Seems repeatable on 9-Stable.  Has been for at least two months (host was 8.x before that).
Comment 1 Hans Petter Selasky 2012-11-14 07:15:39 UTC 
On Tuesday 13 November 2012 22:52:06 Heikki Suonsivu wrote:
> >Number:         173616
> >Category:       usb
> >Synopsis:       LG USB DVD-RW USB STALL
> >Confidential:   no
> >Severity:       serious
> >Priority:       medium
> >Responsible:    freebsd-usb
> >State:          open
> >Quarter:
> >Keywords:
> >Date-Required:
> >Class:          sw-bug
> >Submitter-Id:   current-users
> >Arrival-Date:   Tue Nov 13 22:00:00 UTC 2012
> >Closed-Date:
> >Last-Modified:
> >Originator:     Heikki Suonsivu
> >Release:        FreeBSD 9.1-PRERELEASE amd64
> 
> >Organization:
> bbnetworks.net
> 
> >Environment:
> System: FreeBSD lelu.suonsivu.net 9.1-PRERELEASE FreeBSD 9.1-PRERELEASE #2:
> Sat Nov 10 03:23:41 EET 2012
> root@lelu.suonsivu.net:/usr/obj/usr/src/sys/HSU9 amd64
> 
> dmesg:
> 
> Copyright (c) 1992-2012 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> 	The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 9.1-PRERELEASE #2: Sat Nov 10 03:23:41 EET 2012
>     root@lelu.suonsivu.net:/usr/obj/usr/src/sys/HSU9 amd64
> CPU: AMD Phenom(tm) II X4 965 Processor (3411.49-MHz K8-class CPU)
>   Origin = "AuthenticAMD"  Id = 0x100f43  Family = 0x10  Model = 0x4 
> Stepping = 3
> Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,M
> CA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
> Features2=0x802009<SSE3,MON,CX16,POPCNT>
>   AMD
> Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!
> > AMD
> Features2=0x837ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS
> ,SKINIT,WDT,NodeId> TSC: P-state invariant
> real memory  = 4294967296 (4096 MB)
> avail memory = 3832315904 (3654 MB)
> Event timer "LAPIC" quality 400
> ACPI APIC Table: <070512 APIC1458>
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> FreeBSD/SMP: 1 package(s) x 4 core(s)
>  cpu0 (BSP): APIC ID:  0
>  cpu1 (AP): APIC ID:  1
>  cpu2 (AP): APIC ID:  2
>  cpu3 (AP): APIC ID:  3
> ioapic0 <Version 2.1> irqs 0-23 on motherboard
> kbd1 at kbdmux0
> ctl: CAM Target Layer loaded
> acpi0: <070512 XSDT1458> on motherboard
> acpi0: Power Button (fixed)
> acpi0: reservation of fee00000, 1000 (3) failed
> acpi0: reservation of ffb80000, 80000 (3) failed
> acpi0: reservation of fec10000, 20 (3) failed
> acpi0: reservation of fed80000, 1000 (3) failed
> acpi0: reservation of 0, a0000 (3) failed
> acpi0: reservation of 100000, cfe00000 (3) failed
> cpu0: <ACPI CPU> on acpi0
> cpu1: <ACPI CPU> on acpi0
> cpu2: <ACPI CPU> on acpi0
> cpu3: <ACPI CPU> on acpi0
> attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Event timer "i8254" frequency 1193182 Hz quality 100
> atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
> Event timer "RTC" frequency 32768 Hz quality 0
> hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
> Timecounter "HPET" frequency 14318180 Hz quality 950
> Event timer "HPET" frequency 14318180 Hz quality 450
> Event timer "HPET1" frequency 14318180 Hz quality 450
> Event timer "HPET2" frequency 14318180 Hz quality 450
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
> acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
> acpi_ec0: <Embedded Controller: GPE 0xa> port 0x62,0x66 on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> vgapci0: <VGA-compatible display> port 0xb000-0xb0ff mem
> 0xd0000000-0xdfffffff,0xfe6f0000-0xfe6fffff,0xfe500000-0xfe5fffff irq 18
> at device 5.0 on pci1 hdac0: <ATI (0x970f) HDA Controller> mem
> 0xfe6e8000-0xfe6ebfff irq 19 at device 5.1 on pci1 pcib2: <ACPI PCI-PCI
> bridge> irq 17 at device 9.0 on pci0
> pci2: <ACPI PCI bus> on pcib2
> xhci0: <NEC uPD720200 USB 3.0 controller> mem 0xfe7fe000-0xfe7fffff irq 17
> at device 0.0 on pci2 xhci0: 32 byte context size.
> usbus0 on xhci0
> pcib3: <ACPI PCI-PCI bridge> irq 18 at device 10.0 on pci0
> pci3: <ACPI PCI bus> on pcib3
> atapci0: <JMicron JMB361 UDMA133 controller> port
> 0xcc00-0xcc07,0xc880-0xc883,0xc800-0xc807,0xc480-0xc483,0xc400-0xc40f mem
> 0xfe8ffc00-0xfe8ffdff irq 18 at device 0.0 on pci3 ahci0: <JMicron JMB361
> AHCI SATA controller> at channel -1 on atapci0 ahci0: AHCI v1.10 with 1
> 3Gbps ports, Port Multiplier supported
> ahcich0: <AHCI channel> at channel 0 on ahci0
> ata2: <ATA channel> at channel 0 on atapci0
> ahci1: <ATI IXP700 AHCI SATA controller> port
> 0xa000-0xa007,0x9000-0x9003,0x8000-0x8007,0x7000-0x7003,0x6000-0x600f mem
> 0xfe4ffc00-0xfe4fffff irq 19 at device 17.0 on pci0 ahci1: AHCI v1.20 with
> 6 6Gbps ports, Port Multiplier supported
> ahcich1: <AHCI channel> at channel 0 on ahci1
> ahcich2: <AHCI channel> at channel 1 on ahci1
> ahcich3: <AHCI channel> at channel 2 on ahci1
> ahcich4: <AHCI channel> at channel 3 on ahci1
> ahcich5: <AHCI channel> at channel 4 on ahci1
> ahcich6: <AHCI channel> at channel 5 on ahci1
> ohci0: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe4fe000-0xfe4fefff irq
> 18 at device 18.0 on pci0 usbus1 on ohci0
> ehci0: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xfe4ff800-0xfe4ff8ff
> irq 17 at device 18.2 on pci0 usbus2: EHCI version 1.0
> usbus2 on ehci0
> ohci1: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe4fd000-0xfe4fdfff irq
> 18 at device 19.0 on pci0 usbus3 on ohci1
> ehci1: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xfe4ff400-0xfe4ff4ff
> irq 17 at device 19.2 on pci0 usbus4: EHCI version 1.0
> usbus4 on ehci1
> pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
> hdac1: <ATI SB600 HDA Controller> mem 0xfe4f4000-0xfe4f7fff irq 16 at
> device 20.2 on pci0 isab0: <PCI-ISA bridge> at device 20.3 on pci0
> isa0: <ISA bus> on isab0
> pcib4: <ACPI PCI-PCI bridge> at device 20.4 on pci0
> pci4: <ACPI PCI bus> on pcib4
> fwohci0: <VIA Fire II (VT6306)> port 0xdc00-0xdc7f mem
> 0xfe9fb800-0xfe9fbfff irq 22 at device 7.0 on pci4 fwohci0: OHCI version
> 1.10 (ROM=1)
> fwohci0: No. of Isochronous channels is 4.
> fwohci0: EUI64 00:1e:8c:00:00:e4:87:16
> fwohci0: Phy 1394a available S400, 2 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> firewire0: <IEEE1394(FireWire) bus> on fwohci0
> fwe0: <Ethernet over FireWire> on firewire0
> if_fwe0: Fake Ethernet address: 02:1e:8c:e4:87:16
> fwe0: Ethernet address: 02:1e:8c:e4:87:16
> fwip0: <IP over FireWire> on firewire0
> fwip0: Firewire address: 00:1e:8c:00:00:e4:87:16 @ 0xfffe00000000, S400,
> maxrec 2048 dcons_crom0: <dcons configuration ROM> on firewire0
> dcons_crom0: bus_addr 0xc76d0000
> fwohci0: Initiate bus reset
> fwohci0: fwohci_intr_core: BUS reset
> fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER
> mode ohci2: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem
> 0xfe4fc000-0xfe4fcfff irq 18 at device 20.5 on pci0 usbus5 on ohci2
> pcib5: <ACPI PCI-PCI bridge> at device 21.0 on pci0
> pci5: <ACPI PCI bus> on pcib5
> re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port
> 0xe800-0xe8ff mem 0xfdfff000-0xfdffffff,0xfdff8000-0xfdffbfff irq 16 at
> device 0.0 on pci5 re0: Using 1 MSI-X message
> re0: Chip rev. 0x2c000000
> re0: MAC rev. 0x00000000
> miibus0: <MII bus> on re0
> rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
> rgephy0:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX,
> 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master,
> 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow,
> 1000baseT-FDX-flow-master, auto, auto-flow re0: Ethernet address:
> f4:6d:04:15:87:ff
> ohci3: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe4f3000-0xfe4f3fff irq
> 18 at device 22.0 on pci0 usbus6 on ohci3
> ehci2: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xfe4ff000-0xfe4ff0ff
> irq 17 at device 22.2 on pci0 usbus7: EHCI version 1.0
> usbus7 on ehci2
> acpi_button0: <Power Button> on acpi0
> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> orm0: <ISA Option ROM> at iomem 0xd3000-0xd5fff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> ppc0: cannot reserve I/O port range
> acpi_throttle0: <ACPI CPU Throttling> on cpu0
> hwpstate0: <Cool`n'Quiet 2.0> on cpu0
> Timecounters tick every 1.000 msec
> firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0)  (me)
> firewire0: bus manager 0
> IP Filter: v4.1.28 initialized.  Default = pass all, Logging = enabled
> ipfw2 (+ipv6) initialized, divert enabled, nat enabled, rule-based
> forwarding enabled, default to accept, logging disabled DUMMYNET 0 with
> IPv6 initialized (100409)
> load_dn_sched dn_sched FIFO loaded
> load_dn_sched dn_sched PRIO loaded
> load_dn_sched dn_sched QFQ loaded
> load_dn_sched dn_sched RR loaded
> load_dn_sched dn_sched WF2Q+ loaded
> hdacc0: <ATI RS690/780 HDA CODEC> at cad 0 on hdac0
> hdaa0: <ATI RS690/780 Audio Function Group> at nid 1 on hdacc0
> pcm0: <ATI RS690/780 (HDMI)> at nid 3 on hdaa0
> hdacc1: <Realtek ALC892 HDA CODEC> at cad 0 on hdac1
> hdaa1: <Realtek ALC892 Audio Function Group> at nid 1 on hdacc1
> pcm1: <Realtek ALC892 (Rear Analog 7.1/2.0)> at nid 20,22,21,23 and 24,26
> on hdaa1 pcm2: <Realtek ALC892 (Front Analog)> at nid 27 and 25 on hdaa1
> pcm3: <Realtek ALC892 (Rear Digital)> at nid 30 on hdaa1
> pcm4: <Realtek ALC892 (Onboard Digital)> at nid 17 on hdaa1
> usbus0: 5.0Gbps Super Speed USB v3.0
> usbus1: 12Mbps Full Speed USB v1.0
> usbus2: 480Mbps High Speed USB v2.0
> usbus3: 12Mbps Full Speed USB v1.0
> usbus4: 480Mbps High Speed USB v2.0
> usbus5: 12Mbps Full Speed USB v1.0
> usbus6: 12Mbps Full Speed USB v1.0
> usbus7: 480Mbps High Speed USB v2.0
> ugen0.1: <0x1033> at usbus0
> uhub0: <0x1033 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
> ugen1.1: <ATI> at usbus1
> uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
> ugen2.1: <ATI> at usbus2
> uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
> ugen3.1: <ATI> at usbus3
> uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
> ugen4.1: <ATI> at usbus4
> uhub4: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
> ugen5.1: <ATI> at usbus5
> uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
> ugen6.1: <ATI> at usbus6
> uhub6: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
> ugen7.1: <ATI> at usbus7
> uhub7: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
> uhub5: 2 ports with 2 removable, self powered
> uhub6: 4 ports with 4 removable, self powered
> uhub1: 5 ports with 5 removable, self powered
> uhub3: 5 ports with 5 removable, self powered
> uhub0: 4 ports with 4 removable, self powered
> ada0 at ahcich1 bus 0 scbus2 target 0 lun 0
> ada0: <WDC WD30EZRS-00J99B0 80.00A80> ATA-8 SATA 2.x device
> ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada0: Command Queueing enabled
> ada0: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
> ada0: Previously was known as ad8
> ada1 at ahcich2 bus 0 scbus3 target 0 lun 0
> ada1: <ST32000542AS CC34> ATA-8 SATA 2.x device
> ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada1: Command Queueing enabled
> ada1: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
> ada1: Previously was known as ad10
> ada2 at ahcich3 bus 0 scbus4 target 0 lun 0
> ada2: <ST32000542AS CC34> ATA-8 SATA 2.x device
> ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada2: Command Queueing enabled
> ada2: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
> ada2: Previously was known as ad12
> ada3 at ahcich4 bus 0 scbus5 target 0 lun 0
> ada3: <WDC WD20EARS-00MVWB0 51.0AB51> ATA-8 SATA 2.x device
> ada3: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada3: Command Queueing enabled
> ada3: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
> ada3: Previously was known as ad14
> ada4 at ahcich6 bus 0 scbus7 target 0 lun 0
> ada4: <WDC WD30EZRX-00MMMB0 80.00A80> ATA-8 SATA 3.x device
> ada4: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
> ada4: Command Queueing enabled
> ada4: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
> ada4: Previously was known as ad18
> SMP: AP CPU #2 Launched!
> SMP: AP CPU #1 Launched!
> cd0 at ata2 bus 0 scbus1 target 0 lun 0
> cd0: <HL-DT-ST DVDRAM GSA-4167B DL11> Removable CD-ROM SCSI-0 device
> cd0: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes)
> SMP: AP CPU #3 Launched!
> cd0: Attempt to query device size failed: NOT READY, Medium not present
> Timecounter "TSC-low" frequency 13326119 Hz quality 800
> uhub7: 4 ports with 4 removable, self powered
> GEOM_MIRROR: Device mirror/leluroot launched (1/2).
> GEOM_MIRROR: Device leluroot: rebuilding provider ada1p3.
> GEOM_MIRROR: Device mirror/lelu-root launched (1/1).
> GEOM_MIRROR: Device mirror/lelu-u launched (2/2).
> GEOM_JOURNAL: Journal 3960267491: mirror/lelu-root contains data.
> GEOM_JOURNAL: Journal 3960267491: mirror/lelu-root contains journal.
> GEOM_JOURNAL: Journal mirror/lelu-root clean.
> GEOM_JOURNAL: Journal 769953320: mirror/lelu-u contains data.
> GEOM_JOURNAL: Journal 769953320: mirror/lelu-u contains journal.
> GEOM_JOURNAL: Journal mirror/lelu-u clean.
> Root mount waiting for: GJOURNAL GJOURNAL usbus4 usbus2
> uhub4: 5 ports with 5 removable, self powered
> uhub2: 5 ports with 5 removable, self powered
> ugen2.2: <vendor 0x1a40> at usbus2
> uhub8: <vendor 0x1a40 USB 2.0 Hub MTT, class 9/0, rev 2.00/1.00, addr 2> on
> usbus2 uhub8: MTT enabled
> Root mount waiting for: usbus2
> uhub8: 4 ports with 4 removable, self powered
> Root mount waiting for: usbus2
> ugen2.3: <vendor 0x2109> at usbus2
> uhub9: <vendor 0x2109 USB2.0 Hub, class 9/0, rev 2.00/2.95, addr 3> on
> usbus2 uhub9: 4 ports with 4 removable, self powered
> Root mount waiting for: usbus2
> ugen2.4: <vendor 0x1a40> at usbus2
> uhub10: <vendor 0x1a40 USB 2.0 Hub MTT, class 9/0, rev 2.00/1.00, addr 4>
> on usbus2 uhub10: MTT enabled
> Root mount waiting for: usbus2
> uhub10: 4 ports with 4 removable, self powered
> ugen2.5: <vendor 0x050d> at usbus2
> uhub11: <vendor 0x050d USB 2.0 Hub MTT, class 9/0, rev 2.00/1.00, addr 5>
> on usbus2 uhub11: MTT enabled
> Root mount waiting for: usbus2
> uhub11: 7 ports with 7 removable, self powered
> Root mount waiting for: usbus2
> ugen2.6: <Logitech> at usbus2
> ums0: <Logitech USB Receiver, class 0/0, rev 1.10/9.10, addr 6> on usbus2
> ums0: 5 buttons and [XYZ] coordinates ID=0
> Root mount waiting for: usbus2
> ugen2.7: <Unicomp Inc> at usbus2
> ukbd0: <Keyboard Interface> on usbus2
> kbd2 at ukbd0
> usbd_set_config_index: could not read device status: USB_ERR_SHORT_XFER
> Root mount waiting for: usbus2
> ugen2.8: <BUFFALO> at usbus2
> umass0: <MSC Bulk-Only Transfer> on usbus2
> umass0:  8070i (ATAPI) over Bulk-Only; quirks = 0x0100
> umass0:9:0:-1: Attached to scbus9
> Trying to mount root from ufs:/dev/mirror/leluroot [rw,async]...
> cd1 at umass-sim0 bus 0 scbus9 target 0 lun 0
> cd1: <Optiarc DVD RW AD-7560S SB01> Removable CD-ROM SCSI-0 device
> cd1: 40.000MB/s transfers
> cd1: cd present [278530 x 2048 byte records]
> usbd_set_config_index: could not read device status: USB_ERR_SHORT_XFER
> ugen2.9: <BUFFALO> at usbus2
> umass1: <MSC Bulk-Only Transfer> on usbus2
> umass1:  8070i (ATAPI) over Bulk-Only; quirks = 0x0100
> umass1:10:1:-1: Attached to scbus10
> cd2 at umass-sim1 bus 1 scbus10 target 0 lun 0
> cd2: <Optiarc DVD RW AD-7590S 1.J0> Removable CD-ROM SCSI-0 device
> cd2: 40.000MB/s transfers
> cd2: Attempt to query device size failed: NOT READY, Medium not present -
> tray closed re0: link state changed to UP
> 
> >Description:
> LG external USB DVD-RW fails.
> 
> ugen2.3: <product 0x2502 vendor 0x0424> at usbus2, cfg=0 md=HOST spd=HIGH
> (480Mbps) pwr=SAVE ugen2.9: <Super Multi Rewriter HLDS Inc.> at usbus2,
> cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
> 
> Kernel says the following:
> 
> ugen2.3: <vendor 0x0424> at usbus2
> uhub9: <vendor 0x0424 product 0x2502, class 9/0, rev 2.00/0.01, addr 3> on
> usbus2 uhub9: 2 ports with 2 removable, self powered
> ugen2.9: <HLDS Inc.> at usbus2
> umass1: <HLDS Inc. Super Multi Rewriter, class 0/0, rev 2.00/0.00, addr 9>
> on usbus2 umass1:  SCSI over Bulk-Only; quirks = 0x0100
> umass1:10:1:-1: Attached to scbus10
> cd2 at umass-sim1 bus 1 scbus10 target 0 lun 0
> cd2: <HL-DT-ST DVD-RAM GSA-E20N 1.03> Removable CD-ROM SCSI-0 device
> cd2: 40.000MB/s transfers
> cd2: Attempt to query device size failed: NOT READY, Medium not present
> usb_alloc_device: set address 10 failed (USB_ERR_STALLED, ignored)
> usbd_setup_device_desc: getting device descriptor at addr 10 failed,
> USB_ERR_STALLED usbd_req_re_enumerate: addr=10, set address failed!
> (USB_ERR_STALLED, ignored) usbd_setup_device_desc: getting device
> descriptor at addr 10 failed, USB_ERR_STALLED usbd_req_re_enumerate:
> addr=10, set address failed! (USB_ERR_STALLED, ignored)
> usbd_setup_device_desc: getting device descriptor at addr 10 failed,
> USB_ERR_STALLED ugen2.10: <Unknown> at usbus2 (disconnected)
> uhub_reattach_port: could not allocate new device
> usb_alloc_device: set address 10 failed (USB_ERR_STALLED, ignored)
> usbd_setup_device_desc: getting device descriptor at addr 10 failed,
> USB_ERR_STALLED usbd_req_re_enumerate: addr=10, set address failed!
> (USB_ERR_STALLED, ignored) usbd_setup_device_desc: getting device
> descriptor at addr 10 failed, USB_ERR_STALLED usbd_req_re_enumerate:
> addr=10, set address failed! (USB_ERR_STALLED, ignored)
> usbd_setup_device_desc: getting device descriptor at addr 10 failed,
> USB_ERR_STALLED ugen2.10: <Unknown> at usbus2 (disconnected)
> uhub_reattach_port: could not allocate new device
> usb_alloc_device: set address 10 failed (USB_ERR_STALLED, ignored)
> usbd_setup_device_desc: getting device descriptor at addr 10 failed,
> USB_ERR_STALLED usbd_req_re_enumerate: addr=10, set address failed!
> (USB_ERR_STALLED, ignored) usbd_setup_device_desc: getting device
> descriptor at addr 10 failed, USB_ERR_STALLED usbd_req_re_enumerate:
> addr=10, set address failed! (USB_ERR_STALLED, ignored)
> usbd_setup_device_desc: getting device descriptor at addr 10 failed,
> USB_ERR_STALLED ugen2.10: <Unknown> at usbus2 (disconnected)
> uhub_reattach_port: could not allocate new device
> uhub_reattach_port: port 2 reset failed, error=USB_ERR_STALLED
> uhub_reattach_port: device problem (USB_ERR_STALLED), disabling port 2
> ugen2.3: <vendor 0x0424> at usbus2 (disconnected)
> uhub9: at uhub8, port 4, addr 3 (disconnected)
> ugen2.9: <HLDS Inc.> at usbus2 (disconnected)
> umass1: at uhub9, port 1, addr 9 (disconnected)
> (cd2:umass-sim1:1:0:0): lost device, 1 refs
> (cd2:(pass7:umass-sim1:1:umass-sim1:1:0:0:0): removing device entry
> 0): passdevgonecb: devfs entry is gone
> 
> When trying to access the drive, device not configured error results.
> 

Hi,

Can you try 9-stable?

--HPS
Comment 2 Martin Wilke freebsd_committer freebsd_triage 2015-12-25 05:00:43 UTC 
Feedback timeout 3 years plus.